[wojoo]

Please give me a hint because I don't know where to look for the problem anymore ... I installed a new reversing camera, of course I uploaded the parameters, coded. 5F and parking sensors coded and I don't want to eject the camera. I get the error External control short circuit to ground B13C311


The image appears for literally 3 seconds and the information from the parking sensors is temporarily unavailable (because the camera does not extend)

If I apply power directly to the motor from the camera, it slides out without any problems

Is something badly coded in 5F? maybe the camera is messed up?

The lid opening works fine

CAM 5Q0980556B Passat B8

[icardiag]

What is the coding of camera unit 6C?
When you put the reverse gear in, the VW badge is not opening?

[wojoo]

Code:

I did as below

Add new module to gateway installation list

19 → adaptation → Installation list → specified installations - Camera System Rear View → coded

Disable RVC-LOW and enable RVC-HIGH in MIB module
5F → Long Coding → Byte: 19 → Bit: 4 → disable
5F → adaptation → Car Function List BAP Gen2 → VPS_0x0B → activated
5F → adaptation → Car Function List BAP Gen2 → VPS_0x0B_msg_bus → Comfort data bus



Enable camera support in parktronic module
Some cars will have module 0x76 available instead of 0x10.
10 → Long Coding → Byte: 02 → Bit: 4 → enable
10 → Long Coding → Byte: 02 → Bit: 5 → disable

Enable camera BAP communication
6C → Long Coding → Byte: 10  → Bit 6 BAP for display data

Code vehicle and region
6C → Long Coding → Byte: 00 → vehicle brand
6C → Long Coding → Byte: 01 → vehicle class and generation
6C → Long Coding → Byte: 02 → vehicle body type
6C → Long Coding → Byte: 03 → region

Code vehicle optional equipment
6C → Long Coding → Byte: 04  → Bit 0 Trailer Control Unit (J345) installed
6C → Long Coding → Byte: 04  → Bit 1 Optical Parking Sensors (OPS) installed
6C → Long Coding → Byte: 04  → Bit 2 ParkSteer Assist (PLA) installed
6C → Long Coding → Byte: 04  → Bit 5 DSG/Automatic Transmission installed
6C → Long Coding → Byte: 04  → Bit 6 Swinging Logo installed
6C → Long Coding → Byte: 04  → Bit 7 Electric Parking Brake (EPB) installed
6C → Long Coding → Byte: 10  → Bit 2 Trailer Towing Assistant (TTA/ARA) Mechanical installed
6C → Long Coding → Byte: 10  → Bit 3 Trailer Towing Assistant (TTA/ARA) Optical installed
6C → Long Coding → Byte: 10  → Bit 4 Tow Bar (AHK) installed
6C → Long Coding → Byte: 10  → Bit 5 Rollback recognition

Enable all 4 view modes in camera module
6C → Long Coding → Byte: 07 → Bit: 0 → enable (standard 90° view)
6C → Long Coding → Byte: 07 → Bit: 1 → enable (parallel parking assist view)
6C → Long Coding → Byte: 07 → Bit: 2 → enable (towing view)
6C → Long Coding → Byte: 07 → Bit: 4 → enable (fish-eye/cross-traffic view)

When I turn on the reverse gear, nothing happens, only the image from the camera appears for 3 seconds and after a while there is an error that the parking sensors are unavailable and there is an error in 6C

---

Coding 5F -> 02840201FF0000005111000400080A001F0100E4012004009F

Coding 6C -> 0184020163002017000040

[Versus]

Camera brand new? Or used ?

[icardiag]

What harnes have you used? The chinese supplied harnesses tend to be wrong a lot of times. At least this is my experience, I had to correct the harness...

[wojoo]

Camera brand new? Or used ?

Brand New 3G0827469JB

---

What harnes have you used? The chinese supplied harnesses tend to be wrong a lot of times. At least this is my experience, I had to correct the harness...

my cables do not have the long yellow cable that is visible in the picture.



The yellow cable only goes from the 4 pin plug to the 8 pin plug

[wojoo]

please see if the bundle of these cables is ok?






Isn't the yellow with red in the 4-pin cube interchanged?