Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

NCSExpert coding DSC56 in an R55 with K/DCAN
03-07-2023, 15:10 PM,
Post: #1
NCSExpert coding DSC56 in an R55 with K/DCAN
Following on from my auto to manual conversion, the only module I haven’t done a default code to since I changed the VO is the DSC module, as I get a comms error whenever I try to run SG_Codieren against the DSC.

I gather there’s some slight changes between auto and manual so would like to get it coded. Do I have to use an ICOM, or is there something I’m doing wrong? All other modules work with NCSExpert.

Thanks.
Quote this message in a reply
04-07-2023, 06:07 AM,
Post: #2
RE: NCSExpert coding DSC56 in an R55 with K/DCAN
DSC56 is very picky. Try coding it with the original FA to see if it is the setup or just unsupported coding.
Quote this message in a reply
04-07-2023, 07:16 AM,
Post: #3
RE: NCSExpert coding DSC56 in an R55 with K/DCAN
Icom needed for R5X 2nd generation
Quote this message in a reply
04-07-2023, 08:39 AM,
Post: #4
RE: NCSExpert coding DSC56 in an R55 with K/DCAN
(04-07-2023, 07:16 AM)blax123 Wrote:  Icom needed for R5X 2nd generation

For the DSC specifically?

Because I don’t for the other modules, apart from anything on the MOST bus.
Quote this message in a reply
04-07-2023, 08:47 AM,
Post: #5
RE: NCSExpert coding DSC56 in an R55 with K/DCAN
Main problem with some modules is that they need large (as in 128 to near 250 bytes) data packets. ICOM handles that without any issues. 100% of chinesium DCANs DO NOT. They just truncate data (around 120-ish or 140-ish bytes, that was years ago so I do not remember actual number) and OF COURSE you will get errors.

To solve this you could reflash your cable with ediabaslib firmware. That is IF your cable is built using PROPER hardware inside of it and not cheaped down to death components.

Thats solves 95% of cases of modules not working with such cables.
Quote this message in a reply
[+] 1 user says Thank You to Node for this post
04-07-2023, 11:16 AM,
Post: #6
RE: NCSExpert coding DSC56 in an R55 with K/DCAN
R5X 2nd Gen DSC is unfortunately not compatible with DCAN. With ediabaslib firmware not too.
Quote this message in a reply
04-07-2023, 14:33 PM,
Post: #7
RE: NCSExpert coding DSC56 in an R55 with K/DCAN
I’ve been looking for a good reason to buy an ICOM…

But then we get into genuine ICOM vs clone etc.

I’ll do some reading, but are there any threads with details about how to navigate this minefield and make the right choices?
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  FEM Not working with ENET but works wtih DCAN armenh7 1 87 11 hours ago
Last Post: Marx
XZBMW SSD Creator Ncsexpert (New Tool) scorpium59 542 38,118 Yesterday, 16:04 PM
Last Post: Mefiuu92
  BMW F10 RHD to LHD coding? morto 10 1,221 Yesterday, 06:57 AM
Last Post: muskatas
XZBMW G15 remember last driving mode & ECO PRO MSA memory coding duss46 7 342 26-03-2024, 18:56 PM
Last Post: duss46
XZBMW coding g12 remote key /m display redog4dy 5 194 26-03-2024, 07:23 AM
Last Post: Siki78
  Some news, secure coding coming to new bikes :/ Node 8 1,015 25-03-2024, 15:13 PM
Last Post: RuleNormaliai
  Need help coding out SOS BMW E60 tigre 8 200 24-03-2024, 21:25 PM
Last Post: jararak
  Engine swap E60 535d --> E61 530d coding advice requested Stratofortress 9 306 23-03-2024, 14:59 PM
Last Post: Simoniak
  BMW E87 swap M5 V10 coding cluster Pedrom92 0 99 20-03-2024, 22:50 PM
Last Post: Pedrom92
XZBMW G20- Higher capacity battery coding hallamnet 2 307 19-03-2024, 07:06 AM
Last Post: MasterGt

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content