[Samsara69]

reset sdm program sdm.

of course sdm can be reset, even opcom in 2009 had it.

DO NOT RESET ENGINE ECU.

What is SDM ?

I have only FVDI and Launch.

ECM already reset...

[mattydr67]

SDM-Sensor Diagnostic Modul (Airbag)
Corsa D
SDM Temic
-Programm the VIN in the SDM
-Programm the CAN modul in the SDM
The SDM is a part of the Corsa D immobilizer system and the car will doesn't start untill SDM ( AIrbag ) hasn't been matched.
-Programm the Security Code in the SDM
-Programm the VAriant Configuration of the SDM
When the configuration is programmed and the error codes are cleared, the error code light should still be flashing, and the this error code is stored: B1001 = Airbag Modul not locked
-Start Self-Test and if no other error codes are found then lock the SDM ( Airbag modul )
if you find other error codes the investigate whether to configuration is wrong or there is still a fault in your system.
-Take care: After locking the SDM, the configuration cannot be changed. Only the Seat Belt warning indicator can n ot put on or off.

Good luck

P.S. - if the SDM is locked you cannot unlock it. I am using a virgin dump from a virgin SDM and I programm/flash it by OP-COM Advanced

[Samsara69]

The SDM is a part of the Corsa D immobilizer system and the car will doesn't start untill SDM ( AIrbag ) hasn't been matched.

As I explained there's no reset option for SRS/SDM and SRS is not replaced , only BCM .

After 13V story (I think system need more than 12V) ,there's no security time waiting.

Maybe OP-COM can reset SRS but don't have it.

The car had a flat battery problem and corrupted BCM.

[mattydr67]

Dear Sir I don't know what are you talikg about or whiuch OP-COM are you using but OP-COM has this function under Programmin button in left side menu:
Reset SDM
Programm SDM
Programm VIN
SDM Configuration status
SDM Configuration
All you need is CARPASS
Programm Low-Speed Can Bus Configuration
Clear Deployment Record

Good luck

[Samsara69]

Dear Sir I don't know what are you talikg about or whiuch OP-COM are you using 

I understand your explanation but I don't have OP-COM.

I have only FVDI and Launch but no one give option to reset SDM.

But it's mandatory to reset SDM when replace only BCM?

[mattydr67]

I think Yes if you changed BCM

Good luck

[Samsara69]

I think Yes if you changed BCM

Good luck

Thanks dear.
I found Global TIS with keygen, can use it with AVDI passthrough? 

SDM has these DTC too , need to solve them before reset SDM?

B0051-00 Squib Circuits Activated (Crash) 
B0055-00 Side Airbag Activated Present
B0021-0D Passenger Side Airbag Squib Circuit High Resistance

[mattydr67]

Yes you have to solve that issues.
As I read in your post above you own a FVDI but not a AVDI
Original AVDI is a passthru and can be used with Glo al Tis
FVDI isn't a passthru so cannot be used with Global Tis.

Good luck

[Samsara69]

As I read in your post above you own a FVDI but not a AVDI

I also have AVDI  but not for OPEL ,it's why I not mentioned.

I hope will fix this Corsa this week 

[mattydr67]

No problemss I just mentioned your oportunities by your words.
If you have AVDI then this is really good to use it with SPS Programming, last GDS2 and Tech2win for Opel/Vauxhall.
Take my advice and buy a real OP-COM. Will help you a lot in Opel/Vauxhall cars near your FVDI and AVDI.
Anyway I wish you to solve that Corsa D
Good luck