Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Diagbox run on windows10 ?
22-08-2015, 14:21 PM,
Post: #1
PPeugeot  Diagbox run on windows10 ?
I want to upgrade windows 10, when diagbox can run on it.

Which version can support win10 ?
Quote this message in a reply
22-08-2015, 15:49 PM,
Post: #2
RE: Diagbox run on windows10 ?
Maybe read a bit on forum before asking these questions, so you will now better answer for your costumers wondering
Quote this message in a reply
[+] 2 users say Thank You to mladen76 for this post
24-08-2015, 16:37 PM,
Post: #3
RE: Diagbox run on windows10 ?
Hello,

Diagbox at the moment cannot run in Win 10 wink
Quote this message in a reply
25-08-2015, 11:49 AM,
Post: #4
RE: Diagbox run on windows10 ?
No Diagbox dont work in Windows 10

ne pas installer Windows 10(in french) = dont install windows 10 (in english)

   
Quote this message in a reply
11-09-2015, 01:54 AM,
Post: #5
RE: Diagbox run on windows10 ?
I have just successfully finished installing DiagBox v7.76 on Windows 10 x86 for fun, and it works...
What you need to consider are 4 points:
1- You are probably installing (Windows 10) as GPT, you may need to change to MBR, so that you can use IDE (Legacy) hard disk controller, else you will get the dreaded error 0.. Changing from (AHCI) to IDE may impose speed penalty; depending on your hardware..
2- You need to install .NET 3.5 if you want to install DiagBox v7.66 or above. I also had Firefox installed.
3- You (may) need to plug-in the Lexia interface and install the drivers "ACTIAPnPInstaller.exe" before installing DiagBox v7.01 to ensure the multyinstance driver is installed.
4- You need to run DiagBox as administrator or in XP compatibility mode for v7.74 and above. Otherwise you will get a message to reactivate.

DiagBox v7.76 is the latest and "may be" the last from Actia while moving to v8.xx. I don't think any further development is expected for v7.xx, they are unlikely to support a "sunset" product, the release of the new "A.1281 Z" interface could be an indication!!


Attached Files Thumbnail(s)
       
Actia_Drivers.txt
File Type: .txt
Downloaded: 162 times
Size: 72 bytes

Quote this message in a reply
[+] 12 users say Thank You to Simple for this post
13-09-2015, 20:29 PM,
Post: #6
RE: Diagbox run on windows10 ?
Can you explane this a litle..thanks

1- You are probably installing (Windows 10) as GPT, you may need to change to MBR, so that you can use IDE (Legacy) hard disk controller, else you will get the dreaded error 0.. Changing from (AHCI) to IDE may impose speed penalty; depending on your hardware..
Quote this message in a reply
14-09-2015, 07:24 AM,
Post: #7
RE: Diagbox run on windows10 ?
First some (main) definitions,

Controller/Mode types:
• IDE (Integrated Drive Electronics) is the older HDD 40/44/80 pin parallel ATA interface drive. Setting this mode in the BIOS allows the newer SATA drive to emulate an old Parallel ATA drive (Suitable for Windows XP which did not support SATA at that time).
• AHCI (Advanced Host Controller Interface) supports newer faster and larger drives and has the NCQ (Native Command Queuing) extension, which allows hard disk drives to internally optimize read and write commands execution.

Partition types:
• MBR (Master Boot Record) cannot address more than 2.2TB drives and is limited to 4 primary partitions max.
• GPT (GUID Partition Table) supports partitions of more than 2TB.

Installing DiagBox on Windows where the BIOS is set to AHCI (for better SATA drive utilization) usually fails giving error 0. But it installs and runs on hard disks configured as IDE.

If your BIOS is set to AHCI and windows is installed on a GPT partition, Windows 10 will NOT boot (but Linux will) when you change the BIOS setting to IDE. So in order to boot Windows 10 with the BIOS set to IDE, the partition type needs to be changed to MBR first, then you set the BIOS to IDE or Legacy before installing DiagBox.

However, I have changed the type of Disk on my Windows 10 from IDE to SATA, and my DiagBox current installation still works, see attached photo !!!…

The best and easiest way is to add the other controller type and boot into Windows so that the drivers are loaded and Windows can boot either way before changing from one type to the other.


Attached Files Thumbnail(s)
   
Reputation: +1 - imdady [+1]
Quote this message in a reply
[+] 2 users say Thank You to Simple for this post
01-11-2015, 19:34 PM,
Post: #8
RE: Diagbox run on windows10 ?
Diagbox runs on windows 10 64bit with gpt til version 7.66 after that version i must activate again
Quote this message in a reply
[+] 2 users say Thank You to satelitedream for this post
02-11-2015, 11:36 AM,
Post: #9
RE: Diagbox run on windows10 ?
I don't understand why people need Win 10 on a diagnostic computer. Who want to do diagnostic can best buy a second hand PC for diagnostic only and a PC for personal use. For diagnostic use you don't need a super PC. PSA is clear! Don't update to Win 10.
Quote this message in a reply
[+] 2 users say Thank You to Geri for this post
17-12-2015, 19:42 PM,
Post: #10
RE: Diagbox run on windows10 ?
I just want to confirm that DiagBox still works well with Windows 10 "Redstone" (OS Build 11082.1000) 32 bit, provided that:

1- Hard Disk Controller is set to IDE/Legacy (not AHCI or SCSI),
2- Partition type is MBR (not GPT),
3- .NET 3.5 is installed,
4- Run DiagBox as Administrator..

Photo attached.


Attached Files Thumbnail(s)
   
Quote this message in a reply
[+] 4 users say Thank You to Simple for this post


Possibly Related Threads…
Thread Author Replies Views Last Post
  PSA Diagbox VCI Interfaces alexturbo 18 6,457 27-12-2023, 21:45 PM
Last Post: apol
PPeugeot DIAGBOX 2021 9.85 FULL INSTALATION akli 6 2,537 26-12-2023, 20:21 PM
Last Post: Le-Mans
PCitroen DIAGBOX online walczaklu 10 8,544 03-12-2023, 12:57 PM
Last Post: mattydr67
  DiagBox 7+Updates+Firmware+Drivers+Tools (Magnet) Simple 33 35,302 22-11-2023, 06:16 AM
Last Post: Jeppo
PPeugeot Diagbox 9.129 activation request dadoa4 4 2,349 09-11-2023, 09:59 AM
Last Post: bovhec
  diagbox 9.150 stasi 5 2,045 16-09-2023, 19:41 PM
Last Post: stasi
  DiagBox Language Change Simple 16 17,333 14-09-2023, 10:01 AM
Last Post: żarówka
  DIAGBOX help needed installing mars2moon 4 997 23-07-2023, 18:45 PM
Last Post: J415UNNY
PPeugeot Diagbox 9.91 VmWare gabi2008 6 4,178 23-07-2023, 18:42 PM
Last Post: J415UNNY
  diagbox latest ? Chad69 1 823 09-06-2023, 22:28 PM
Last Post: simo2k

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content