[SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61) +---- Thread: [SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing (/showthread.php?tid=16771) |
||||||||||
RE: [SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing - ayerkn - 20-11-2017 I had updated my DME module ISTA an got the Engine malfunction - reduced power fault this must be retrofitted to remove the fault ? I have downloaded the document above this is same for all E90 RHD an can be done DIY Another thing where can I get the parts my local BMW dealer was giving me a lead time that next year, I just need to get that fault out to sell the vehicle. Any other ideas or help would be appreciated RE: [SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing - Pzolee - 17-05-2018 Hi boys. What is solution with MSD80N43 ista p software update? Thanks all. RE: [SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing - CarlosF11 - 02-08-2018 (24-11-2016, 22:40 PM)Czozen Wrote: New Version of spdaten 3.60 has new software that repair this Bug! I'm still not convinced the latest software version solves the vacuum sensor error on our 2010 N43 with automatic transmission. There's new software in 3.65 (E8X-18-07-520), I would like to install this version but first I want to make sure the error doesn't come up again afterwards. I'm not planning on actually installing the vacuum sensor. Up 'till now I got the problem fixed with WinKfp and downgrading the ECU software (like you can read in earlier posts here). Anyone able to comment on this? RE: [SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing - Thomas M. - 02-08-2018 This error means that u need retrofit sensor. BMW dealer did it for me 4 months ago for free. Warranty case. They just retrofitted new sensor and reprogrammed all car again. RE: [SOLVED] E91 N43 Engine malfunction - reduced power after ISTA-P 3.59.2.001 flashing - HestonDiag - 03-08-2018 The problem is chain guides break on the N43 and bits of plastic end up in the sump. In some cases these bits end up blocking the oil pickup meaning there is oil running round the engine but pressure a bit low. The vacuum pump is one of the last bits to be lubricated, so this issue can end up in a reduction of available vacuum. Cars with manual gearbox already have a vaccum sensor fitted as part of the start-stop system. This is so if the car is stopped and the footbrake is repeatedly applied causing available vacuum to drop too low, the engine will start automatically to make sure brake vacuum assistance is always available. Automatic cars didn't have this sensor from factory but the quality enhancement campaign involves fitting this sensor to automatic cars for free, and reprogramming auto and manual cars. The software update adds functionality to detect if the vacuum pump is not performing as required so it can display a warning to the driver. Also a check is performed to see if the chain has stretched and I've heard of cases where everything has been replaced for free on cars well out of warranty.
|