DigiProg 3 mk3 mondeo facelift 2007 correction - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: DigiProg 3 mk3 mondeo facelift 2007 correction (/showthread.php?tid=2549) Pages:
1
2
|
DigiProg 3 mk3 mondeo facelift 2007 correction - neo123 - 16-02-2014 Hi there new to the forum. I was wondering if anyone can help. I recently purchased digiprog 3 v 4.85 from china. I am trying to adjust the mileage for a 2007 mk3 Mondeo. It states I need the hc12 cable. THe cable I have has different colours to what the cables they show on the instructions. My HC12 cable shows red, black, light orange and brown. Whereas the manual shows white, brown, green and yellow. How can I match the wires. In addition my speedo 32 pins are different to the ones in the instructions. Does anyone know where I can solder the positive and negative and which wires goes on the reset. thanks in advance pics below any help appreciated [img][/img] RE: DigiProg 3 mk3 mondeo facelift 2007 correction - teerak2uk - 16-02-2014 Look at the 25 pin on ST51 plug Brown. 13 Green 17 Yellow. 18 White 25 Ignore your colours just go by the pin numbers as the chinks prob ran out if the correct coloured cable RE: DigiProg 3 mk3 mondeo facelift 2007 correction - neo123 - 16-02-2014 have they given me the wrong cable, this is how its connected RE: DigiProg 3 mk3 mondeo facelift 2007 correction - sashxxx - 16-02-2014 If it is clone will not work with hc12 RE: DigiProg 3 mk3 mondeo facelift 2007 correction - neo123 - 16-02-2014 What do you mean clone? I purchase digiprog 3 v.4.85 from china can this not do Mondeos? RE: DigiProg 3 mk3 mondeo facelift 2007 correction - sashxxx - 16-02-2014 China clone don't have support hc12 RE: DigiProg 3 mk3 mondeo facelift 2007 correction - neo123 - 16-02-2014 On the digiprog 3 there is an option for hc12 and the hcs12. They gave manual too but the colours are different. When I select Mondeo and hc12 on digiprog it says u need cable 51, I have the cable 51. Just don't know how to connect up cause colours are different. RE: DigiProg 3 mk3 mondeo facelift 2007 correction - Kris81 - 16-02-2014 Digiprog will do it by obd connector. RE: DigiProg 3 mk3 mondeo facelift 2007 correction - neo123 - 16-02-2014 (16-02-2014, 20:52 PM)Kris81 Wrote: Digiprog will do it by obd connector. but this is the mk3 Mondeo not the mk4 Mondeo. Mk3 Mondeo u need to take the speedos out? RE: DigiProg 3 mk3 mondeo facelift 2007 correction - Kris81 - 16-02-2014 My mistake, u can read this by bdm points on the back of the clock, with standard programmer ( upa or xprogm. |