Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
How to enable BMW Apps E92 M3?
10-08-2019, 00:47 AM,
(This post was last modified: 10-08-2019, 00:54 AM by Vishnurpatel.)
Post: #12
|
|||
|
|||
RE: How to enable BMW Apps E92 M3?
am in exatcly same boat stwert! we in this together bro!
i have combox telematics but the ididot didnt order 6FL the usb port in arm rest. so i am going to code that in for ipod connection and 6NF witch is for the phone ingrasion, once this was done i was hoping to figure out bmw apps. Issue is trying to figure out what fimwhere we are on, and then how this FCS coding works. I think if our firmwhere is too old we are fucked, and need to flash the firmware and this can take ages over D/K Cable. So i might have to pay someone on ebay to do it! but they all quoting over 200! I dont think u coded the cic i dirive or the media moudals thats why u might not see the change or your firmwhere is old. Adding Option 6FL Step One – Adding $6FL: Open INPA and verify that it is connected properly. Close INPA when verified. Open NCSEXPERT and load profile Expertenmosus (Werkseinstellung). Press VIN/ZCS/FA (F1) Press ZCS/FA f. ECU (F3) Choose the E89 chassis Choose CAS or NFRM Press Enter FA (F2) Choose E89 Enter VIN: OK Add $6FL OK Press Back (F6) Press Process ECU (F4) Choose CAS Press Change Job (F2) Choose FA_WRITE OK Press Execute job (F3) Press Change ECU (F1) –> Choose NFRM Press Execute job (F3) Close NCS Expert Step Two – Coding changes to CIC: Open INPA and verify that it is connected properly. Close INPA when verified. Open NCSEXPERT and load profile Expertenmosus (Werkseinstellung). Press VIN/ZCS/FA (F1) Press ZCS/FA f. ECU (F3) Choose the E89 chassis Choose CAS or NFRM Press Back (F6) Press Process ECU (F4) Choose CIC Press Change Job (F2) Choose SG_CODIEREN Press Execute job (F3) Step Tree – Coding changes to MEDIA: Open INPA and verify that it is connected properly. Close INPA when verified. Open NCSEXPERT and load profile Expertenmosus (Werkseinstellung). Press VIN/ZCS/FA (F1) Press ZCS/FA f. ECU (F3) Choose the E89 chassis Choose CAS or NFRM Press Back (F6) Press Process ECU (F4) Choose MEDIA Press Change Job (F2) Choose SG_CODIEREN Press Execute job (F3) you need to do this but with $6NR. am not going to try this until iv confirmed the firmware just seen this is an old thred! ![]() |
|||
« Next Oldest | Next Newest »
|
Messages In This Thread |
How to enable BMW Apps E92 M3? - by Stewartps - 06-01-2019, 21:04 PM
RE: How to enable BMW Apps E92 M3? - by ruben_17non - 06-01-2019, 21:39 PM
RE: How to enable BMW Apps E92 M3? - by Stewartps - 06-01-2019, 21:49 PM
RE: How to enable BMW Apps E92 M3? - by ruben_17non - 06-01-2019, 22:09 PM
RE: How to enable BMW Apps E92 M3? - by Stewartps - 06-01-2019, 23:02 PM
RE: How to enable BMW Apps E92 M3? - by ruben_17non - 06-01-2019, 23:16 PM
RE: How to enable BMW Apps E92 M3? - by Stewartps - 06-01-2019, 23:32 PM
RE: How to enable BMW Apps E92 M3? - by ruben_17non - 06-01-2019, 23:42 PM
RE: How to enable BMW Apps E92 M3? - by Stewartps - 06-01-2019, 23:49 PM
RE: How to enable BMW Apps E92 M3? - by ruben_17non - 07-01-2019, 00:00 AM
RE: How to enable BMW Apps E92 M3? - by Stewartps - 07-01-2019, 15:09 PM
RE: How to enable BMW Apps E92 M3? - by Vishnurpatel - 10-08-2019, 00:47 AM
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content