Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Not abble to read micronas
28-03-2024, 20:26 PM,
Post: #1
|
|||
|
|||
Not abble to read micronas
Hello, i have xprog v6.5 with dongle.
I tried to read my dash from audi a3 8p, i tried to read the cdc3217 and eprom but i don't abble to read. The connections are ok because i readed the mileage, vin, pin from the dash, the problem is on the read icon because this icon are in gray and unabble to use. I tried to make new bin in xprog but same...without success, how to read my cdc and eprom? |
|||
28-03-2024, 20:46 PM,
Post: #2
|
|||
|
|||
RE: Not abble to read micronas
what version of windows are you using, as far as i know 6.5 will only work properly on win 7 64bit
|
|||
28-03-2024, 20:47 PM,
Post: #3
|
|||
|
|||
RE: Not abble to read micronas
|
|||
28-03-2024, 21:10 PM,
(This post was last modified: 28-03-2024, 21:15 PM by al70.)
Post: #4
|
|||
|
|||
RE: Not abble to read micronas
have a read through this thread, i think it's same dash
https://cartechnology.co.uk/showthread.php?tid=76272 are you adding 12v to xprog ? |
|||
Reputation: +1 - dabaca [+1] | |||
28-03-2024, 22:20 PM,
Post: #5
|
|||
|
|||
RE: Not abble to read micronas
No, i don't added 12v, how to do that on the cilindrical connector?
It should not apear the read icon to use if is missing 12v? Because when i select device, dash, audi, cdc3217 and eprom the read icon stay in gray and i can't use it... (Is my first time using xprog) |
|||
28-03-2024, 22:24 PM,
(This post was last modified: 28-03-2024, 22:26 PM by al70.)
Post: #6
|
|||
|
|||
RE: Not abble to read micronas
i only have 5.11, not sure about 6.5, try 12v, yes round socket
post some pics of the cluster pcb, there's a solution for read without lifting pins from chip, i'll look for it |
|||
29-03-2024, 06:27 AM,
(This post was last modified: 29-03-2024, 06:36 AM by sebiosip.)
Post: #7
|
|||
|
|||
RE: Not abble to read micronas
I post photos with my pcb from cluster, with vin,pin readed and changed (i changed the VIN and mileage).
Photo with the read problem, the read aption (glases) is in gray and not usable. My cluster is a 8p0920931s, i buyed the cluster to swap my old cluster because i have old cluster without display and my cluster start to missing the rpm . The cluster is working on my car because i have immo off on ecu and i buyed the key from donor car, i don't have safe message, i activated the needle sweep, oil themperature (but is in submenu), the boost and lap timer is not working. For that i need to read the cdc for backup if i have problems and rewrite the cdc with a dump what have the boost, lap, etc. This is my cluster history Here is another photo |
|||
29-03-2024, 11:16 AM,
Post: #8
|
|||
|
|||
RE: Not abble to read micronas
Click new, top left hand corner
|
|||
29-03-2024, 15:44 PM,
Post: #9
|
|||
|
|||
RE: Not abble to read micronas
I tried but not work, clicked new but the read icon is not accessible
|
|||
29-03-2024, 17:17 PM,
(This post was last modified: 29-03-2024, 17:57 PM by al70.)
Post: #10
|
|||
|
|||
RE: Not abble to read micronas
Try to read it as Audi TT,
Maybe antivirus removed part of the software, try reinstalling software |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content