Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
19-06-2015, 21:18 PM,
(This post was last modified: 19-06-2015, 21:24 PM by mista.)
Post: #11
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
Ok this is the mark of the eeprom? no?
hi this is the eeprom that i need to read with sop8 adaptater |
|||
19-06-2015, 21:34 PM,
Post: #12
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
Nm24c04 soic
fairchild |
|||
19-06-2015, 21:40 PM,
(This post was last modified: 19-06-2015, 22:00 PM by mista.)
Post: #13
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
Ok where do you see the nm into the picture ....??
thanx a lot for help i will check this driver into the tl866 software tomorrow and i will report thanx a lot for help someone can confirm me if there fairchild nm 24c04 soic or dsop8 as a driver on tl866 software ? thanx a lot |
|||
20-06-2015, 06:50 AM,
Post: #14
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
(19-06-2015, 21:40 PM)mista Wrote: Ok where do you see the nm into the picture ....?? i dont see nm on picture but i see v8 so far i know fm was up to v3 or on most programmers not presented so nm is for sure v8 on my other 2 programmers |
|||
20-06-2015, 07:13 AM,
Post: #15
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
Ok thanx for information m'y friend
which programmer do you use ? You think it will be ok with tl866? |
|||
20-06-2015, 07:16 AM,
Post: #16
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
I have many others but tl will work ok
|
|||
20-06-2015, 07:20 AM,
Post: #17
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
Ok thanx a lot i will try it and report thanx a lot for help my friend
|
|||
20-06-2015, 13:33 PM,
Post: #18
|
|||
|
|||
RE: Tl866 a read eeprom 24c02 with soic clamp (bora 2000)
Hi everyone i come back with news loool i read the chip one time but i don't know if the file is correct ? someone can check the pin and km? or which software can i use for this? i put the file hope it s okay
many thanx to sv2hqx for help it was the good driver but when i put the chip 24c04 into the adaptater sop8 i didnt push into the corner i put the chip like that so i didn't succes to read the chip i put it a little bit strongly so i break the chip now but before to break it i read it one time hope it will be ok question where can i buy this chip ? do i need to buy the same serial number ? mark ? etc? i make a save file with k+can commander of the eeprom can i write this file from k can commander by tl866a when i put it the new chip? thanx for help |