Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ VW EDC17CP14 and Galletto v54 write in boot mode
29-04-2016, 21:35 PM,
Post: #11
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Hi
It is not error only information about checksum, when you write checksumed files will all ok.. |
|||
29-04-2016, 22:08 PM,
Post: #12
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Galletto it is just sayng that he can not do checksumm.
That is all. H does not modify anithing. If it is asking you for the original file, than he is doing-it so that he does not kill the ecu... Iff you are 100 % shure that the file is ok, than just write-it. |
|||
29-04-2016, 22:33 PM,
Post: #13
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Yes, but I hit OK, and nothing happens.
I hit cancel, and nothing happens. Or should I wait longer? I have my file and checksums are OK. I am not worried about checksums being wrong (I correct them in WinOLS), I just want the program to continue with flashing. ______________________ Alternate theory: Is it possible to attempt to flash the big 4.2 MB 'all' file (int flash, ext flash, eeprom combined)? can I paste my changes there, and checksums too? |
|||
29-04-2016, 22:36 PM,
Post: #14
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Bad galletto.
Try Ktag and kess. You will be better. |
|||
29-04-2016, 22:38 PM,
(This post was last modified: 29-04-2016, 23:18 PM by Enabled.)
Post: #15
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Is Kess recommended or Ktag?
They both have leads for tricore boot mode, no? Shipping will take quite a bit of time. (29-04-2016, 22:33 PM)Enabled Wrote: ______________________ The answer is YES I flashed the original 4224kb 'all' file back to the ecu successfully. Galletto skips checksum correction for the ALL file. Risky, but I guess I was brave enough. The boot pin accidentally untouched, and galletto stopped and told me to remove power and reconnect. WHILE FLASHING. Nearly peed my pants. I repositioned boot pin, reconnected power, and it continued error free! After, I did a verification read of all. 100% identical to original Now I will paste my internal flash mods (with checksum corrected already) into the 4224kb file, and flash that. |
|||
30-04-2016, 01:52 AM,
Post: #16
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
It worked!!! 0. Read Original ALL with Galletto boot mode. It will give you "All" file (4,224kb), internal flash+external flash+eeprom, (in my case). 1. Paste mod internal flash (make sure checksums are already correct) into the original 'all' file. Align correctly. Internal flash starts at 00, so it is easy. 2. Triple check that the paste is ok! 3. Flash modded "all" file in Galletto. This is done using "Write All" button. 4. It takes much longer to flash a file with differences. It took about 6+ minutes on first part - internal flash. It went to 100%, then to 75% and up to 100% slowly many times. Total over 10 minutes. 5. Read All to verify! 6. Compare with Hex Editor. Proofs: 1. Writing mod internal flash All 4224kb file. 2. Read All for verification 3. Compare! |
|||
Reputation: +1 - vanos batam [+1] | |||
30-04-2016, 17:37 PM,
Post: #17
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Good job...!!!
-------------------------' Indonesia..........
|
|||
30-04-2016, 19:43 PM,
Post: #18
|
|||
|
|||
RE: VW EDC17CP14 and Galletto v54 write in boot mode
Tested today in car. Car started, DPF functions are all gone.
Do I need to disconnect any sensors for this car? |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content