Please Make Sure You Read The Forum Rules! , Thanks for registering We are glad you have chosen to be a part of our community :) Please do not use email addresses, website URLs, Skype info, or any other contact info as your Username.
  1. ObdToolUsa

  2. Martech

  3. obdresource

    obdresource.com
  4. Piwis tester II

  5. OBD Center

  6. ChiPTuninG



Post Reply 
B2139 transit connect 2004
11-01-2017, 21:38 PM
Post: #1
LFord B2139 transit connect 2004
Can anyone shed some light on this fault? the led in the dash is flashing 22 I've tried a known good pcm and pats module I've tried deleting keys and recoding them ive checked power and ground and can wires at fuel pump but still no joy headbang it's the 1.8 tddi engine
Find all posts by this user
Quote this message in a reply
11-01-2017, 22:59 PM
Post: #2
RE: B2139 transit connect 2004
(11-01-2017 21:38 PM)Cbenno Wrote:  Can anyone shed some light on this fault? the led in the dash is flashing 22 I've tried a known good pcm and pats module I've tried deleting keys and recoding them ive checked power and ground and can wires at fuel pump but still no joy headbang it's the 1.8 tddi engine

If the battery has been flat or you have cranked the engine over with a flat battery then the most likely cause is the PCM and the FIP have lost their synchronisation

Make sure the battery is fully charged, jump leads on another car are not good enough as you need a good steady voltage, then run module initialisation in IDS and the engine should then run. drive
Find all posts by this user
Quote this message in a reply
12-01-2017, 07:36 AM
Post: #3
RE: B2139 transit connect 2004
(11-01-2017 22:59 PM)Merseycruise Wrote:  
(11-01-2017 21:38 PM)Cbenno Wrote:  Can anyone shed some light on this fault? the led in the dash is flashing 22 I've tried a known good pcm and pats module I've tried deleting keys and recoding them ive checked power and ground and can wires at fuel pump but still no joy headbang it's the 1.8 tddi engine

If the battery has been flat or you have cranked the engine over with a flat battery then the most likely cause is the PCM and the FIP have lost their synchronisation

Make sure the battery is fully charged, jump leads on another car are not good enough as you need a good steady voltage, then run module initialisation in IDS and the engine should then run. drive
I tried that first with ids it just stayed the same with a permanent b2139 code it does crank but nothing else.
Find all posts by this user
Quote this message in a reply
19-01-2017, 21:45 PM
Post: #4
RE: B2139 transit connect 2004
Hello error code:B2141 and blink:22= NVM Configuration failure. No security ID exchange between PCM and fuel injection pump control module, vehicle does not start : solution New PCM or fuel injection pump control module REFER to the WDS. Select the PATS test and follow the instructions on the screen.
error code B2139 and blink 23= Data mismatch (received data does not match what was expected). Security messages do not match between PCM and fuel injection pump control module, vehicle does not start solutin: New PCM or fuel injection pump control module REFER to the WDS. Select the PATS test and follow the instructions on the screen. cut from ford etis manual on connect 2004
i have seen some where it was injektion pump that there was defekt new pump and reinstall pump in pats menu

rgds sev
Find all posts by this user
Quote this message in a reply
 Thanks given by: Cbenno , fraserauto
20-01-2017, 19:52 PM
Post: #5
RE: B2139 transit connect 2004
(19-01-2017 21:45 PM)sev611 Wrote:  Hello error code:B2141 and blink:22= NVM Configuration failure. No security ID exchange between PCM and fuel injection pump control module, vehicle does not start : solution New PCM or fuel injection pump control module REFER to the WDS. Select the PATS test and follow the instructions on the screen.
error code B2139 and blink 23= Data mismatch (received data does not match what was expected). Security messages do not match between PCM and fuel injection pump control module, vehicle does not start solutin: New PCM or fuel injection pump control module REFER to the WDS. Select the PATS test and follow the instructions on the screen. cut from ford etis manual on connect 2004
i have seen some where it was injektion pump that there was defekt new pump and reinstall pump in pats menu

rgds sev

Thanks for the response that was going to be my next step as I have tried the pcm the pats receiver and checked all wiring so fuel pump ecu it is
Find all posts by this user
Quote this message in a reply
Post Reply 


Bookmarks

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
0Engine Ford Connect 1.8 2008 PATS IMMO Fault HELP!,,,,,,, in shadowstill8 5 485 05-04-2016 20:57 PM
Last Post: sev611
  How to take speed limiter of a 2015 transit in new2theroad 7 778 23-03-2016 21:44 PM
Last Post: sev611

Forum Jump:


User(s) browsing this thread:
1 Guest(s)

Return to TopReturn to Content