[pdc]

Hi

my cas cafd is 0000000F 005 025 058
my hkfm is 000007c8 006 008 004-same as yours
my trunk just open with foot does not close,but the a pillar A button open and close the trunk.

the function is : SCH TOEHKI
Check also; PHY TASTER;TASTER FBD ;SCH FBD;

Tomorrow i will check swf version

One member sent me a PM, that for smart closing I need CAFD version 7 file CAFD_000007C8_007_xxx_xxx

If I detect CAF from SWE it shows me for SWFL_00000D9A_006_004_000 just:
CAFD_000007C8_006_004_000
CAFD_000007C8_006_008_004
Only way to get CAFD_000007C8_007_xxx_xxx is to flash HKFM module with different SWFL version.
If I change my VO to LCI car and update i-level factory to LCI. I get an error when calculating TAL. Doesn´t anybody know how to flash HKFM module with custom SWFL?

pdc: please check your SWFL version of your HKFM module, thanks!

[pdc]

Hi my swfl is:

HKFM_LS 6b: 00000D9A_006_004_000
CAS : 0000074XX_007_012_000
XX=C,D,E,F

[mr_nitroz]

I GOT IT FINALLY WORKING!!!

Thanks to all, who have been giving me tips to enable this option, especially Almaretto, who provide me his BTLD, CAFD and SWFL versions.
So after days of trying I found a way how to enable smart closing on pre-lci F10. You need to have full psdzdata, e-sys and enet cable or icom.

Here is how to:

-connect with your car in e-sys

-select TAL-Calculating

-read and activate your VO, read ecu

-under KIS/SVT target: select complete flash, check your shipment and target i-level that is filled correctly, press calculate

-check you actual HKFM_LS versions, mine were:
BTLD_00000D99_006_004_000
CAFD_000007C8_006_008_004
HWEL_00000D98_004_000_000
SWFL_00000D9A_006_004_000

-under KIS/SVT save your SVT, then press edit

-find HKFM_LS module, open standardSVK and edit BTLD, CAFD and SWFL to those values:
BTLD_00000D99_006_006_000
CAFD_000007C8_007_000_015
SWFL_00000D9A_010_002_000

-save your SVT and press back, confirm reloading modified SVT file

-check that you have new values under HKFM_LS module

-under TAL press calculation, save your TAL and press execute

-now in TAL-Processing check software availability, check just HKFM_LS and select BLFLASH, SWDEPLOY and CDDEPLOY

-with ignition turned on and engine off press START

-wait 3 minutes until bootloader, software and coding will be processed

-if all went OK, you should see green process bar and successful information in log

-under Coding, FDL code:
CAS:
CAM_SMART_CLOSE - aktiv
to get enabled closing boot lid with your remote control and inside footwell button you need to code again your HKFM module to those values:
HKFM => 3010 => TASTER_FBD => aktiv
HKFM => 3010 => SCH_TOEHKI => aktiv
HKFM => 3010 => SCH_FBD => aktiv

-run Rheingold/ISTA_D, delete all errors and in service function start inicialisation of boot lid

Congratulations, you have now successfully loaded custom HKFM SW with smart closing!

[jaki]

Because the main thing is solved, I humble borrow this thread for my problem:
I have F11 built 12/2010 and I have tried to "retrofit" smart opener to it.
H/W is a piece of cake, that is done, but in HKM module I don't have anything related to Smart opener = SMO coding options. I tested with an different cafd file and there was needed options.
My question (I'm still a newbie with esys), can I just change cafd to an other, which esys lists or accepts?
Then there seems to be two cafd's. I didn't save or code anything, that was my only finding.
My car is updated somewhere in 2013, but I guess HKM module has the original s/w.
Is t better to flash the whole car for newets s/w before doing anything more?

[mr_nitroz]

Jaki:
- in FRM you need to code smart_opener_verbaut to aktiv
- you can try newer CAFD (use detect CAF for SWE) and just code HKFM, no problem
- if you updated car in 2013 with 2013 i-level you should have HKFM already ready for smart opener

For mine SW version of HKFM - SWFL_00000D9A_006_004_000
I had 2 CAFD versions, one had SMO and other one didn´t.

[jaki]

Jaki:
- in FRM you need to code smart_opener_verbaut to aktiv
- you can try newer CAFD (use detect CAF for SWE) and just code HKFM, no problem
- if you updated car in 2013 with 2013 i-level you should have HKFM already ready for smart opener

For mine SW version of HKFM - SWFL_00000D9A_006_004_000
I had 2 CAFD versions, one had SMO and other one didn´t.

Thank's for fast and prompt reply!
When flashing car with ISTA/P it forces quite often to flash only a couple of modules. It is possible that BMW Vertragshändler mekanic has chosen just to flash necessary units only, and maybe HKM was not in the list in that time.
- Yes, FRM I have already coded.
- I think that I have similar swfl in my HKM, I have to check, but yes, I inject an other cafd and code it with that.
However, I will flash my car completely later, currently I'm only eager to see that my retrofit works. And finally, yes, I know that I have code everything again after flashing

[B5M3W5d]

I GOT IT FINALLY WORKING!!!

Thanks to all, who have been giving me tips to enable this option, especially Almaretto, who provide me his BTLD, CAFD and SWFL versions.
So after days of trying I found a way how to enable smart closing on pre-lci F10. You need to have full psdzdata, e-sys and enet cable or icom.

Here is how to:

-connect with your car in e-sys

-select TAL-Calculating

-read and activate your VO, read ecu

-under KIS/SVT target: select complete flash, check your shipment and target i-level that is filled correctly, press calculate

-check you actual HKFM_LS versions, mine were:
BTLD_00000D99_006_004_000
CAFD_000007C8_006_008_004
HWEL_00000D98_004_000_000
SWFL_00000D9A_006_004_000

-under KIS/SVT save your SVT, then press edit

-find HKFM_LS module, open standardSVK and edit BTLD, CAFD and SWFL to those values:
BTLD_00000D99_006_006_000
CAFD_000007C8_007_000_015
SWFL_00000D9A_010_002_000

-save your SVT and press back, confirm reloading modified SVT file

-check that you have new values under HKFM_LS module

-under TAL press calculation, save your TAL and press execute

-now in TAL-Processing check software availability, check just HKFM_LS and select BLFLASH, SWDEPLOY and CDDEPLOY

-with ignition turned on and engine off press START

-wait 3 minutes until bootloader, software and coding will be processed

-if all went OK, you should see green process bar and successful information in log

-under Coding, FDL code:
CAS:
CAM_SMART_CLOSE - aktiv
to get enabled closing boot lid with your remote control and inside footwell button you need to code again your HKFM module to those values:
HKFM => 3010 => TASTER_FBD => aktiv
HKFM => 3010 => SCH_TOEHKI => aktiv
HKFM => 3010 => SCH_FBD => aktiv

-run Rheingold/ISTA_D, delete all errors and in service function start inicialisation of boot lid

Congratulations, you have now successfully loaded custom HKFM SW with smart closing!

Do you know the part numbers required for this retrofit?

[mr_nitroz]

Https://www.bimmerfest.com/forums/attach...1427972952