Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Xprog programming device silent error
16-02-2018, 23:03 PM,
(This post was last modified: 16-02-2018, 23:06 PM by dil6222.)
Post: #1
|
|||
|
|||
Xprog programming device silent error
Hello all messed about with my xprog removed original atmega and hotair another atmega on so I could program it programmed verify etc ok.
Then when I soldered back my original atmega there was loud pop from somewhere the only place I can guess is the 11mhz crystal or 4.7pf capacitor is only thing that's near. Tryed it and xprog gives device silent error I tried to reprogram atmega but wouldn't program verify errors so i soldered new one on and programmed OK so maybe was MCU that went pop unsure lol. Now when I plug in my xprog and try to read any chip I get device silent error still and no LEDs on xprog lightup i can reprogram atmega no problems but still same device silent error. Any ideas ? Maybe 4.7pf cap or 11.0592 crystal just below MCU ? If mine or others posts and info are helpful please give thanks/rep
|
|||
17-02-2018, 00:00 AM,
(This post was last modified: 17-02-2018, 00:02 AM by volavka.)
Post: #2
|
|||
|
|||
RE: Xprog programming device silent error
seems a fw problem
i'm using this fw and work well https://www.cartechnology.co.uk/showthre...?tid=13345 Good luck BEST CHIPTUNING SERVICE BY Zenter Performance
Contact Skype: zenter-88 Facebook: https://www.facebook.com/ZenterPerformance -------------------------------------------------------------------------------------------------------------- highest Quality ChiPTuninG Files BY PTF Team https://performance-tuningfiles.com/ POWER BY TECHNOLOGY -------------------------------------------------------------------------------------------------------------- BEST CHIPTUNING SERVICE BY Jurebv Contact Skype: live:jure.coric_1 https://files.tuning-makarska.com/ -------------------------------------------------------------------------------------------------------------- - IMMO/ECU , ODO , AIRBAG , CARRADIO , TESTED SOLUTIONS UNDER MY SOFTWARE In progress TUNING STAGE1/DPF/SCR/EGR/TVA/FLAP/ START STOP OFF Software WHAT'S NEWS ! -Steering Angle Sensor Restore For LEXUS,TOYOTA,SUBARU,MITSUBISHI,VAG -Citroen DS5 Steering lock Renew/Write Code by dumps -Passat CCM Repair corrupted dump succes -VAG ECU SIMOS PCR 2.1 KM WITH CRC CORRECTED ! -IMMO OFF For NISSAN/INIFINITI with HITACHI ECU | CPU SH705X -Dacia Dashboard with Fujitsu MB96F6A6 Change km/Block Synchro Dash-ABS -=[Full WinOLS/ECM Titanium User] =- Remember! dirty hands are a sign of clean money шшш.αήkαbôôτ.Ćô.цk |
|||
Reputation: +2 - Marcos [+1] , dil6222 [+1] | |||
17-02-2018, 01:26 AM,
(This post was last modified: 17-02-2018, 19:08 PM by dil6222.)
Post: #3
|
|||
|
|||
RE: Xprog programming device silent error
Thanks volavka firmware isnt the issue I don't think tried to flash the firmware you posted still get device silent.
So maybe is caps its as if xprog doesn't wake not sure any ideas ? Update :tried changing the 4.7uf cap and 11mhz crystal next to MCU no difference still same error what led usually comes on when you plug in xprog green ? Found a cap on underside of board if I hold my voltage tester between the two ends for a second while usb plugged in white bulb on xprog comes on red and stays on until I unplug. when I plug in again it is off till I put tester between pins so might be part of problem anyone got any idea what capacitor I could replace it with ? Also seems about right as pop came from around crystal area near MCU and and the underside cap I mentioned is attached to one of the crystals legs maybe heat from crystal while I was changing MCU popped it Here Right one in circle attached to 11mhz crystal leg just below need to substitute it temporarily value cap I could use anyone? Update: a lot of schematics that use atmega64 has 2 x 22pf caps on legs of crystal so gonna try that first let you know results later If mine or others posts and info are helpful please give thanks/rep
|
|||
18-02-2018, 01:46 AM,
Post: #4
|
|||
|
|||
RE: Xprog programming device silent error
I had same problem, always device silent or sometime start to read but after 15% error, i change my usb cable by new good quality and since no problem.
|
|||
18-02-2018, 02:08 AM,
Post: #5
|
|||
|
|||
RE: Xprog programming device silent error
(18-02-2018, 01:46 AM)rachon Wrote: I had same problem, always device silent or sometime start to read but after 15% error, i change my usb cable by new good quality and since no problem. Hmm don't think it the issue as was working fine before I decided to desolder MCU to program another now since no lights on xprog and device silent error. If mine or others posts and info are helpful please give thanks/rep
|
|||
18-02-2018, 14:20 PM,
(This post was last modified: 18-02-2018, 14:20 PM by rs@chip.)
Post: #6
|
|||
|
|||
RE: Xprog programming device silent error
(18-02-2018, 02:08 AM)dil6222 Wrote:(18-02-2018, 01:46 AM)rachon Wrote: I had same problem, always device silent or sometime start to read but after 15% error, i change my usb cable by new good quality and since no problem. maybe you test your xprog like I see on picture up with wires steel on programing pads and 2GND together like I did in past.. |
|||
18-02-2018, 19:32 PM,
(This post was last modified: 18-02-2018, 19:35 PM by dil6222.)
Post: #7
|
|||
|
|||
RE: Xprog programming device silent error
(18-02-2018, 14:20 PM)rs@chip Wrote:Not sure what you mean explain please what pads where and how to test(18-02-2018, 02:08 AM)dil6222 Wrote:(18-02-2018, 01:46 AM)rachon Wrote: I had same problem, always device silent or sometime start to read but after 15% error, i change my usb cable by new good quality and since no problem. Also what led should be on when plugged in USB and working normal ? Green 1 or the white led that can be green or red ? If mine or others posts and info are helpful please give thanks/rep
|
|||
22-02-2018, 10:41 AM,
Post: #8
|
|||
|
|||
RE: Xprog programming device silent error
He means you must disconnect the programmer from xprog before testing xprog functions
if my post helps please give Reputation and Thanks
|
|||
22-02-2018, 11:23 AM,
(This post was last modified: 22-02-2018, 11:26 AM by dil6222.)
Post: #9
|
|||
|
|||
RE: Xprog programming device silent error
(22-02-2018, 10:41 AM)domelec Wrote: He means you must disconnect the programmer from xprog before testing xprog functions Yeah done that no difference not solved yet still working on it now building PCB so I can program atmega64 standalone without it being on xprog board Thinking about it I pinout programming pins to dsub 9 socket so can plug direct to upa and unplug but the 2 grounds are still connected together when socket is unplugged maybe cause issue I'll check. If mine or others posts and info are helpful please give thanks/rep
|
|||
11-06-2019, 05:03 AM,
Post: #10
|
|||
|
|||
RE: Xprog programming device silent error
Hi. You fix this error. I have same problem?
I got a xprog for free. it is 5.48 on it with another sticker 5.50. on the cd version was 5.50 on it. the problem is that it does not work. When I connect xprog in the usb it is recognized but it does not respond to anything. it always comes the message "Device is Silence" There are no LED lights .. when writing, reading or something I tried to read atmega64 with tl866 but it does not find the atmega64. |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
possible to copy key data from one CAS3 to another? (xprog-m dump) | vilord | 2 | 102 |
02-05-2024, 07:39 AM Last Post: vilord |
|
reccomendation for ecu programming hardware for edc17c10 | theno1pars | 7 | 236 |
07-04-2024, 18:41 PM Last Post: al70 |
|
BCM2 Touareg error 02811 | shasse | 5 | 252 |
13-03-2024, 15:02 PM Last Post: ROD-BENDERS |
|
Key Programming Tool | koziol | 1 | 199 |
06-03-2024, 07:22 AM Last Post: TKservice |
|
read EWS 3 error | stjansdal | 10 | 396 |
28-02-2024, 12:28 PM Last Post: foxportal |
|
New BCM2, new keys, Theft-return, ODIS FAZ1570E error Huracan. | Ratatouille98 | 4 | 372 |
14-02-2024, 19:40 PM Last Post: Ratatouille98 |
|
Solved ✔ cas2 error A0AD | bursuc | 8 | 413 |
10-02-2024, 20:01 PM Last Post: aejanow |
|
2021 Jeep Wrangler 2.0L esl programming | drhg | 0 | 148 |
21-01-2024, 17:45 PM Last Post: drhg |
|
audi a3 ecu pcr2.1 error immo | firas | 6 | 399 |
19-01-2024, 14:18 PM Last Post: 16eddi67 |
|
Solved ✔ Audi Q5 ELV error 02811 | shasse | 2 | 225 |
13-01-2024, 12:00 PM Last Post: shasse |
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content