[ap90500]

There is no need to use Ediabas when using ISTA with ICOM. See attachment for correct settings.

[wrt]

Hi

Does the Icom have a hostname - so we could use that instead of the ip adddress?

No, only IP. Use IToolRadar to make sure that the ICOM connected and see previous post for configuring TCP.

[B1257]

What ip address that i have to set inside eth0 Tcp/ip v4 properties box?

The easiest way is to let your NIC find the IP and subnet automatically. (see ap90050 post, I recommend this settings too)

Than connect the ICOM to the NIC and power it on wait a little bit, after a while the LAN Led should light.

You can verify the IP and subnet of your NIC through the cmd console (run as admin) of Windows. Type in ipconfig /all and the system will show you the IP and subnet address of your NIC´s and of all connected adapters.

If the NIC of the Notebook and the ICOM is on the same subnet ISTA is operating automatically. You dont need Ediabas with the right VCI settings (see ap90050 post).

If the adapter is on a different subnet it will never work, because they cant talk together.

Regards,
B1257

[Stiffmaster]

Hi,

just use ISTA/P from ISPI-Next and you can simple choose your icom by clicking on it

Best regards.

[Vines]

Hi!

Sorry for my English).
If you are using ediabas only on laptop directly connected with car and this laptop without wifi or local connection - maybe this help:

1. TCP & xEthernet
RemoteHost = 169.254.92.38 (for clone ICOM example)

2. Rem - ; ClampHandling = 0 (its useful if you are using EasyConnect, INPA and etc.)

Hi will try your suggestion and give feedback.
Appreciated.

---

Hi

Does the Icom have a hostname - so we could use that instead of the ip adddress?

Hi, Will check if have host name, am I able to check with Itoolrader?

[ap90500]

Hi!

Sorry for my English).
If you are using ediabas only on laptop directly connected with car and this laptop without wifi or local connection - maybe this help:

1. TCP & xEthernet
RemoteHost = 169.254.92.38 (for clone ICOM example)

2. Rem - ; ClampHandling = 0 (its useful if you are using EasyConnect, INPA and etc.)

Hi will try your suggestion and give feedback.
Appreciated.

---

Hi

Does the Icom have a hostname - so we could use that instead of the ip adddress?

Hi, Will check if have host name, am I able to check with Itoolrader?

Forget these things and do configuration like I said.

[Yhwsha]

I have sent him a PM offering to help with the whole thing but no reply.. This is the second thread he opens asking for help

Hello brunofraga
i saw your help, but i try to reach you through PM

Should i edit the ediabas.ini file located in the Ediabas folder on my C:\Ediabas\bin ?

[brunofraga]

I have sent him a PM offering to help with the whole thing but no reply.. This is the second thread he opens asking for help

Hello brunofraga
i saw your help, but i try to reach you through PM

Should i edit the ediabas.ini file located in the Ediabas folder on my C:\Ediabas\bin ?

Here are two options you can use original launcher which doesnt require ediabas to be installed or you can use Bemmerboy loader which require ediabas, when you are doing the installation for ediabas make sure to select enet that way you dont need to touch on the ediabas.ini should work flawless make sure to unistall and install again the ediabas.

PS. I never receive any type of PM from you.

Good Luck

[Aleck]

Icom connects to ISPI directly without any loaders. All soft can work from original icons.
Loader was made to force ISPI works with D-CAN.

[bimmer71]

Easy fix guys , witin icom webpage go to :58000/?CountryCode=Us and edit to static also check box save also set computer to stacit ip just make sure both have same subnet and gateway , or just use a decided router ! also witin icom setup make sure you select ispi next under drop drop tab .