[Marcos]

I'm Running 3.47.10, Can I use this this to update to 3.51.25?

After you remove your 3.47.10 you can use this new release from Beemerboy. Read instructions !
Good Luck

[tuanvo1982]

I have the same message :
"Error : The vehicle could not be identified. Please check the access to the vehicle and check whether the testing-analysis etc."

What I did are :
1. I went to VCI settings and choose the 1st option which is Ediabas
2. Click into identify button the I can see the light is red on the cable. (I think in this case the Com is set up correctly)
3. The Ediabas was working in background

I may need to check which version Ediabas I have installed because people suggest only greater then 7.3 will works with Rheingold.

Also check pin 7-8 actually I don't know about that until read this article

Can you suggest me what I need to do with Ediabas folder in the Rheingold and the Ediabas which I have installed? (Do we have to override that or moving thing around.)

Do I need to set the cable in D-CAN or any mode by K+DCAN utility?

Some people suggest change folder of Ediabas in Rheingold config. Also can I have the link of Ediabas 7.3 or latest one please.

Thanks

[beemerboy88]

I have the same message :
"Error : The vehicle could not be identified. Please check the access to the vehicle and check whether the testing-analysis etc."

What I did are :
1. I went to VCI settings and choose the 1st option which is Ediabas
2. Click into identify button the I can see the light is red on the cable. (I think in this case the Com is set up correctly)
3. The Ediabas was working in background

I may need to check which version Ediabas I have installed because people suggest only greater then 7.3 will works with Rheingold.

Also check pin 7-8 actually I don't know about that until read this article

Can you suggest me what I need to do with Ediabas folder in the Rheingold and the Ediabas which I have installed? (Do we have to override that or moving thing around.)

Do I need to set the cable in D-CAN or any mode by K+DCAN utility?

Some people suggest change folder of Ediabas in Rheingold config. Also can I have the link of Ediabas 7.3 or latest one please.

Thanks

Do not mess with the contents of the Rheingold folder.

[tuanvo1982]

So I should install a new Ediabas in C drive and leave Ediabas in Rheingold there. Do you know we need to setup something with K+DCAN Utility?

[Mrg0721]

I have the same message :
"Error : The vehicle could not be identified. Please check the access to the vehicle and check whether the testing-analysis etc."

What I did are :
1. I went to VCI settings and choose the 1st option which is Ediabas
2. Click into identify button the I can see the light is red on the cable. (I think in this case the Com is set up correctly)
3. The Ediabas was working in background

I may need to check which version Ediabas I have installed because people suggest only greater then 7.3 will works with Rheingold.

Also check pin 7-8 actually I don't know about that until read this article

Can you suggest me what I need to do with Ediabas folder in the Rheingold and the Ediabas which I have installed? (Do we have to override that or moving thing around.)

Do I need to set the cable in D-CAN or any mode by K+DCAN utility?

Some people suggest change folder of Ediabas in Rheingold config. Also can I have the link of Ediabas 7.3 or latest one please.

Thanks

From BMW Standard Tools, install only Ediabas (7.3), make sure to select the box that says USB to Serial and you will need to set COM Port 9

Here are my Ediabas & obd .ini files from my Ediabas folder, if you'd like copy them to your Ediabas --> bin folder

Also make sure, under Device Manager --> Ports, right click USB Serial Port (COM 9) and select Properties --> Port Settings tab --> Advanced and make sure it looks something like this:
   

Sorry if instructions are a little confusing.

[tuanvo1982]

I think I have set up correct because the cable have signal and the led is change when I click identify button. The last thing I will try is use K+DCAN Utility and set it in DCAN and check the pin 7 + 8. I don't know for rheingold + BMW X1 E84 do we need to solder pin 7 and 8 ?

[beemerboy88]

I think I have set up correct because the cable have signal and the led is change when I click identify button. The last thing I will try is use K+DCAN Utility and set it in DCAN and check the pin 7 + 8. I don't know for rheingold + BMW X1 E84 do we need to solder pin 7 and 8 ?

General rule is >2007 = unbridged 7/8

Most people install a switch instead of soldering so it can be used on old and new cars.

[tuanvo1982]

Sorry just a last one. Do I need to modify Ediabas.ini in the Rhleingold\Ediabas ? because once, Rhleingold is running I see the dialog of Ediabas showing it using INI in c:\Ediabas\Ediabas.ini and application using is folder in c:\Rhleingold\Ediabas.
Is that correct?

[beemerboy88]

Sorry just a last one. Do I need to modify Ediabas.ini in the Rhleingold\Ediabas ? because once, Rhleingold is running I see the dialog of Ediabas showing it using INI in c:\Ediabas\Ediabas.ini and application using is folder in c:\Rhleingold\Ediabas.
Is that correct?

doesn't matter. don't modify anything.

[tuanvo1982]

Thank you for all of your helps. Unfortunately it does not work. I will buy another cable. This cable I try use DCAN for dos and windows but got error message like K-Line Echo or not connect to adapter etc. Anyways, I get back to you once I got new cable.