(04-07-2018, 13:38 PM)ROD-BENDERS Wrote:  

(04-07-2018, 13:05 PM)vaki1989 Wrote:  

(04-07-2018, 12:29 PM)ROD-BENDERS Wrote:  

(04-07-2018, 11:31 AM)vaki1989 Wrote:  It doesnt work can we make immo off the new ecu

EDC17CP44

7P5907401D

I need good immo off solution without error P1570.

Thank you!

Here

1. write flash and eprom
2. if not work write ori eprom back and test again.

No it doesnt work can you make immo and dtc off files from the old ecu??

With EDC17 you cannot write files from one ecu to another it doesnt work.

(04-07-2018, 13:47 PM)vaki1989 Wrote:  

(04-07-2018, 13:38 PM)ROD-BENDERS Wrote:  

(04-07-2018, 13:05 PM)vaki1989 Wrote:  

(04-07-2018, 12:29 PM)ROD-BENDERS Wrote:  

(04-07-2018, 11:31 AM)vaki1989 Wrote:  It doesnt work can we make immo off the new ecu

EDC17CP44

7P5907401D

I need good immo off solution without error P1570.

Thank you!

Here

1. write flash and eprom
2. if not work write ori eprom back and test again.

No it doesnt work can you make immo and dtc off files from the old ecu??

With EDC17 you cannot write files from one ecu to another it doesnt work.

i have written them and car started but errors p1570 and p160a with immooff17 i wanted to go off dash lights.
Regards.

(09-10-2017, 10:55 AM)b.ibrahimi Wrote:  

(08-10-2017, 19:52 PM)ale_lagranda Wrote:  Hi mates:

Need adapt immo and VIN for back to original file after diesel gate remap.
Upload BDM read file I have in ECU and BDM read to other car with same software I have before diesel gate.

Thanks in advance..

Hi there,

I already done your files in the other forum. But here it is again.

(15-07-2018, 04:56 AM)cbyriel Wrote:  Hi.

I need some help regarding cloning of a EDC17c64. I just recently learned about not being able to transfer software directly from one EDC17 to another, because of OTP.

My Old ecu is EDC17c64 - 04L906021EQ 7540. I did make a complete backup with K-Tag clone of EPROM and Internal Flash which is included in the "OLD ECU" dir in the attached file.

New ecu is EDC17c64 - 04L906021EQ 6284. I also made a complete backup of that, included in "NEW ECU" dir, of EPROM and Internal Flash.

VIN is VSSZZZ5FZFR058329 if needed.

I have a couple of small question though:
Firsly ofcause if transfer is possible for these 2?

Secondly - before i needed to replace the original ECU i had a tune made, based on the original files from the old ecu - will i be able to use this tune after transfer (if only the EPROM is modded?) - if not - would it be possible to use the tune as the base for the modifications? (if not, too bad - i will have to get it re-made then). Just in case i have included the tune in the "OLD ECU" dir and the file is called .tune

And if ECU's wont match, would it be possible to make a immo off of the old original that i can then use on the new ecu (no warning lights/errorcodes)?

Thanks alot in advance!

(15-07-2018, 17:53 PM)dijo Wrote:  

(15-07-2018, 04:56 AM)cbyriel Wrote:  Hi.

I need some help regarding cloning of a EDC17c64. I just recently learned about not being able to transfer software directly from one EDC17 to another, because of OTP.

New ecu is EDC17c64 - 04L906021EQ 6284. I also made a complete backup of that, included in "NEW ECU" dir, of EPROM and Internal Flash.

VIN is VSSZZZ5FZFR058329 if needed.

I have a couple of small question though:
Firsly ofcause if transfer is possible for these 2?

Secondly - before i needed to replace the original ECU i had a tune made, based on the original files from the old ecu - will i be able to use this tune after transfer (if only the EPROM is modded?) - if not - would it be possible to use the tune as the base for the modifications? (if not, too bad - i will have to get it re-made then). Just in case i have included the tune in the "OLD ECU" dir and the file is called .tune

And if ECU's wont match, would it be possible to make a immo off of the old original that i can then use on the new ecu (no warning lights/errorcodes)?

Thanks alot in advance!

>Hi, something wrong here...
>I get from old ECU this Vin = ZBR070161
>and from new ECU this Vin = ZCR012015
where is data from your Ori ECU from car
because this dont much to Vin= ZFR058329
why

(15-07-2018, 18:34 PM)cbyriel Wrote:  

(15-07-2018, 17:53 PM)dijo Wrote:  

(15-07-2018, 04:56 AM)cbyriel Wrote:  Hi.

I need some help regarding cloning of a EDC17c64. I just recently learned about not being able to transfer software directly from one EDC17 to another, because of OTP.

New ecu is EDC17c64 - 04L906021EQ 6284. I also made a complete backup of that, included in "NEW ECU" dir, of EPROM and Internal Flash.

VIN is VSSZZZ5FZFR058329 if needed.

I have a couple of small question though:
Firsly ofcause if transfer is possible for these 2?

Secondly - before i needed to replace the original ECU i had a tune made, based on the original files from the old ecu - will i be able to use this tune after transfer (if only the EPROM is modded?) - if not - would it be possible to use the tune as the base for the modifications? (if not, too bad - i will have to get it re-made then). Just in case i have included the tune in the "OLD ECU" dir and the file is called .tune

And if ECU's wont match, would it be possible to make a immo off of the old original that i can then use on the new ecu (no warning lights/errorcodes)?

Thanks alot in advance!

>Hi, something wrong here...
>I get from old ECU this Vin = ZBR070161
>and from new ECU this Vin = ZCR012015
where is data from your Ori ECU from car
because this dont much to Vin= ZFR058329
why

Hi! First of all thanks for your time. Okay sorry for the confusion, but that is very wierd. - the vin i wrote was from an ID i made with MPPS not the actual tool i used (KTAG) However i now just looked up the vin in the registration database and it is indeed: VSSZZZ5FZFR058329 however - i also just checked all my read files and the Old Ori file is indeed the file i sent to you, and i have a couple of reads from it and just compared them - they are identical ...

So now i am wondering what could be wrong here, i dont get it?

(15-07-2018, 19:20 PM)dijo Wrote:  

(15-07-2018, 18:34 PM)cbyriel Wrote:  

(15-07-2018, 17:53 PM)dijo Wrote:  

(15-07-2018, 04:56 AM)cbyriel Wrote:  Hi.

I need some help regarding cloning of a EDC17c64. I just recently learned about not being able to transfer software directly from one EDC17 to another, because of OTP.

New ecu is EDC17c64 - 04L906021EQ 6284. I also made a complete backup of that, included in "NEW ECU" dir, of EPROM and Internal Flash.

VIN is VSSZZZ5FZFR058329 if needed.

I have a couple of small question though:
Firsly ofcause if transfer is possible for these 2?

Secondly - before i needed to replace the original ECU i had a tune made, based on the original files from the old ecu - will i be able to use this tune after transfer (if only the EPROM is modded?) - if not - would it be possible to use the tune as the base for the modifications? (if not, too bad - i will have to get it re-made then). Just in case i have included the tune in the "OLD ECU" dir and the file is called .tune

And if ECU's wont match, would it be possible to make a immo off of the old original that i can then use on the new ecu (no warning lights/errorcodes)?

Thanks alot in advance!

>Hi, something wrong here...
>I get from old ECU this Vin = ZBR070161
>and from new ECU this Vin = ZCR012015
where is data from your Ori ECU from car
because this dont much to Vin= ZFR058329
why

Hi! First of all thanks for your time. Okay sorry for the confusion, but that is very wierd. - the vin i wrote was from an ID i made with MPPS not the actual tool i used (KTAG) However i now just looked up the vin in the registration database and it is indeed: VSSZZZ5FZFR058329 however - i also just checked all my read files and the Old Ori file is indeed the file i sent to you, and i have a couple of reads from it and just compared them - they are identical ...

So now i am wondering what could be wrong here, i dont get it?

ups, sorry, i mixed your date with others from another car...
but you shult have for eeprom 64kb and flash 2048KB

(15-07-2018, 19:22 PM)cbyriel Wrote:  

(15-07-2018, 19:20 PM)dijo Wrote:  

(15-07-2018, 18:34 PM)cbyriel Wrote:  

(15-07-2018, 17:53 PM)dijo Wrote:  

(15-07-2018, 04:56 AM)cbyriel Wrote:  Hi.

I need some help regarding cloning of a EDC17c64. I just recently learned about not being able to transfer software directly from one EDC17 to another, because of OTP.

New ecu is EDC17c64 - 04L906021EQ 6284. I also made a complete backup of that, included in "NEW ECU" dir, of EPROM and Internal Flash.

VIN is VSSZZZ5FZFR058329 if needed.

I have a couple of small question though:
Firsly ofcause if transfer is possible for these 2?

Secondly - before i needed to replace the original ECU i had a tune made, based on the original files from the old ecu - will i be able to use this tune after transfer (if only the EPROM is modded?) - if not - would it be possible to use the tune as the base for the modifications? (if not, too bad - i will have to get it re-made then). Just in case i have included the tune in the "OLD ECU" dir and the file is called .tune

And if ECU's wont match, would it be possible to make a immo off of the old original that i can then use on the new ecu (no warning lights/errorcodes)?

Thanks alot in advance!

>Hi, something wrong here...
>I get from old ECU this Vin = ZBR070161
>and from new ECU this Vin = ZCR012015
where is data from your Ori ECU from car
because this dont much to Vin= ZFR058329
why

Hi! First of all thanks for your time. Okay sorry for the confusion, but that is very wierd. - the vin i wrote was from an ID i made with MPPS not the actual tool i used (KTAG) However i now just looked up the vin in the registration database and it is indeed: VSSZZZ5FZFR058329 however - i also just checked all my read files and the Old Ori file is indeed the file i sent to you, and i have a couple of reads from it and just compared them - they are identical ...

So now i am wondering what could be wrong here, i dont get it?

ups, sorry, i mixed your date with others from another car...
but you shult have for eeprom 64kb and flash 2048KB

Phew - lol - great ... eh .. no EEPROM64 kb, flash is 4mb . which i know is correct.. ?!

(15-07-2018, 19:55 PM)dijo Wrote:  

(15-07-2018, 19:22 PM)cbyriel Wrote:  

(15-07-2018, 19:20 PM)dijo Wrote:  

(15-07-2018, 18:34 PM)cbyriel Wrote:  

(15-07-2018, 17:53 PM)dijo Wrote:  >Hi, something wrong here...
>I get from old ECU this Vin = ZBR070161
>and from new ECU this Vin = ZCR012015
where is data from your Ori ECU from car
because this dont much to Vin= ZFR058329
why

Hi! First of all thanks for your time. Okay sorry for the confusion, but that is very wierd. - the vin i wrote was from an ID i made with MPPS not the actual tool i used (KTAG) However i now just looked up the vin in the registration database and it is indeed: VSSZZZ5FZFR058329 however - i also just checked all my read files and the Old Ori file is indeed the file i sent to you, and i have a couple of reads from it and just compared them - they are identical ...

So now i am wondering what could be wrong here, i dont get it?

ups, sorry, i mixed your date with others from another car...
but you shult have for eeprom 64kb and flash 2048KB

Phew - lol - great ... eh .. no EEPROM64 kb, flash is 4mb . which i know is correct.. ?!

mhhhhh, Strange things...