+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: CHIPTUNING (https://cartechnology.co.uk/forumdisplay.php?fid=12)
+--- Thread: Siemens SID801A, read, write ECU (/showthread.php?tid=29453)
Pages:
1
2
RE: Siemens SID801A, read, write ECU - krisrider24 - 10-02-2018
Hello Greek.damjan thank you for your answer.
Mine ktag is a 7.020 and know supports sid801A.
Well I will do this.
And the boot pin wire you removed it from the ground before start dump? Somebody tell me that he got a corrupt dump file if wire not removed before reading.
He checked the dump file with an ori with the help of a hexdecimal editor.
What do you think about this?
What hp was your engine ? Maybe I could compare with ori file below but mine is a 406 2.0 hdi 110
Thank you
RE: Siemens SID801A, read, write ECU - grmsek.damjan - 10-02-2018
Your Ktag 7.020 support sid 801A?
YES,removed..when the warning message appear put ignition off(switch), put boot pin on mass( I put it on black gnd wire),turn ignt. on(switch),after half a second to one second pud down boot pin from mass)..press OK..finally started reading..the same for writing
Mine was 90hp
RE: Siemens SID801A, read, write ECU - krisrider24 - 10-02-2018
I don't want to make any mistakes but i think that it supported in ktag to read write via bootmod and verify checksum please watch pictures and say what you think
sorry it is in french
RE: Siemens SID801A, read, write ECU - grmsek.damjan - 10-02-2018
Interesting, my old Ktag does not have it, I checked with your car select and also checked with protocols
Nowhere SID801a
RE: Siemens SID801A, read, write ECU - krisrider24 - 11-02-2018
Yes i Will let you know if on my 406's friend it is a sid 801A and if it works.
Because I am learning, I saw that the ecu can be too a Bosch and I did not see the car yet. So I don't know which on is set on.
But before to make anything on a car,I phish more informations I can about the differents possibility
it is so interesting.Maybe my update is really interesting and add a lot of cars' ecu
RE: Siemens SID801A, read, write ECU - mexanico1971 - 09-04-2018
width Ktag is very simple to read / write that ecu
RE: Siemens SID801A, read, write ECU - guidotacco - 11-11-2018
that ecu read in bootwith ktag,fgtech, write in obd with kess
RE: Siemens SID801A, read, write ECU - Geri - 12-11-2018
Is it possible to use BDM100 Siemens adapter with Ktag? This adapter works with converter on FG Tech V24 as far as I know. I don(t want to buy original JR-Tag adaptor for a single use.
RE: Siemens SID801A, read, write ECU - klonone - 28-12-2018
Hi, you can buy IOTERMINAL siemens its the best dont need open ecu, read all by obd2
Regards
RE: Siemens SID801A, read, write ECU - Jonathanv8 - 09-02-2019
Hello, I have the same SID801A calculator on a XSARA 2.0 HDI 90 and I am looking to read the mapping by ODB.
I saw that Ayllon308 says he reads with an MPPSV18, read and write by ODB?
I am sorry for my approximate English (I am French)
Thank you in advance
Jonathanv8