+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: Install 10.25" MGU CID on ENTRYNAV2 (G20) (/showthread.php?tid=79575)
Install 10.25" MGU CID on ENTRYNAV2 (G20) - suchpro - 01-06-2023
Hello everyone,
I have ENTRYNAV2 (ID6) and the 8.8" CID on G20 (Live Cockpit Plus). I want to try to upgrade it to the 10.25" screen that comes with MGU.
Old Screen is 8.8" CID GEN2
Manufacturer: ALPINE
рдятNo: 6550 8717540 04
New Screen is 10.25" MGU CID
Manufacturer: Visteon (00125611-10, HW0009, SW004B)
рдятNo: 6550 8798742 04
I've tried changing the VO a couple of ways, but I always end up getting NO SIGNAL.
Tried changing:
Code:
- CID_DISPLAY_RES to 1440_540, 1920_720
- CID_APIX_MODE to apix2, apix3
- CID_DISPLAY_SIZE to 10_25
- CID_DISPLAY_AR to 1_07In my mind, this is a simple display that needs the HU to output the correct resolution/ratio/color over the APIX protocol?
Can help and anyone shed some light on what's going on? Thanks
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - Mwahab - 02-06-2023
Entrynav2 some ppl didn't manage to make it work with 10.25inch 1440 EVO screen, how about MGU one's?
https://cartechnology.co.uk/showthread.php?tid=59825&page=2
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - suchpro - 02-06-2023
True, I saw that post though I was unsure what the issue with the G30 was. The 1440_540 resolution should work with Entrynav2 as the APIX2 protocol supports it, so it was probably just coding, or maybe component protection. Not sure how that protection works.
However, the G20 comes with two screens, the 8.8" 1280x480 screen and the 10.25" 1920x720 screen I believe. People were successful in coding MGU HU from 8.8 1280x480 to 10.25" 1920x720, I want to see if I could make it work with EntryNav2.
Does anybody have any additional info on the Visteon screen or why I might be getting No Signal?
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - Ibrahim24 - 03-06-2023
Might the video cable be the problem?
Maybe it doesn’t give enough voltage through.
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - Garryq - 03-06-2023
Entrynav2 didnt work with 1440_540, 1920_720 resolution
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - suchpro - 03-06-2023
(03-06-2023, 11:47 AM)Garryq Wrote: Entrynav2 didnt work with 1440_540, 1920_720 resolution
Did you ever find out why? Was it a technical limitation or a software issue?
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - Dravil - 26-07-2026
Need your support. I have an F40 with Entrynav2. I installed a larger 10.25-inch display. I also changed the resolution to 1440x540 and set the size to 10.25. All other values have already been adjusted for the larger screen as well. However, I get a 'no signal' message. Can the large display even be installed in the F40, and if so, what else needs to be coded?
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - jaramillo - 26-07-2026
(26-07-2026, 14:31 PM)Dravil Wrote: Need your support. I have an F40 with Entrynav2. I installed a larger 10.25-inch display. I also changed the resolution to 1440x540 and set the size to 10.25. All other values have already been adjusted for the larger screen as well. However, I get a 'no signal' message. Can the large display even be installed in the F40, and if so, what else needs to be coded?
Get MGU, RAM and Dkombi4
RE: Install 10.25" MGU CID on ENTRYNAV2 (G20) - Dravil - 26-07-2026
(26-07-2026, 14:44 PM)jaramillo Wrote:(26-07-2026, 14:31 PM)Dravil Wrote: Need your support. I have an F40 with Entrynav2. I installed a larger 10.25-inch display. I also changed the resolution to 1440x540 and set the size to 10.25. All other values have already been adjusted for the larger screen as well. However, I get a 'no signal' message. Can the large display even be installed in the F40, and if so, what else needs to be coded?
Get MGU, RAM and Dkombi4
That means no way to do it work. Need other рдят5 right?