+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: Solved ✔ Cic update on E series (/showthread.php?tid=89229)
Pages:
1
2
Cic update on E series - alsamaraee - 23-02-2024
Hello
I started with updating the CI63F1 of the cic in a E91 using the ICOM next without the Next B (optic adapter).
As you all may know it will take many hours. I ordered the adapter now I still have the laptop on and the update is ongoing.
My question is: is it ok to terminate the update and started again when I will receive the adapter?
Thanks in advance
RE: Cic update on E series - Gatsby79 - 23-02-2024
The correct sequence to flash it is 63 , 62, and A0
The 63 and A0 must be done using MOST_Auto_Async ediabas protocol and of course icom B
The 62 (gateway) must be flashed by CAN, using base ediabas protocol.
Don't try to flash 62 with most, it will fail .
hope its helps
RE: Cic update on E series - alsamaraee - 23-02-2024
Gatsby79 dateline='[url=tel:1708684328' Wrote: 1708684328[/url]']
The correct sequence to flash it is 63 , 62, and A0
The 63 and A0 must be done using MOST_Auto_Async ediabas protocol and of course icom B
The 62 (gateway) must be flashed by CAN, using base ediabas protocol.
Don't try to flash 62 with most, it will fail .
hope its helps
Thank you for reply and confirming the sequence of update.
My situation now is that i started 63 with icom A(no most) and of course it taking almost 2 days. I am waiting for my B adapter. It is 49% now almost 24 hours left. Is it possible to terminate the update? Or the unit will break?
RE: Cic update on E series - zero9 - 23-02-2024
62 doesnt fail with most
RE: Cic update on E series - Gatsby79 - 23-02-2024
(23-02-2024, 11:44 AM)zero9 Wrote: 62 doesnt fail with most
it fail , 62 must be flashed over Dcan.
RE: Cic update on E series - zero9 - 23-02-2024
Cic does not fail
RE: Cic update on E series - alsamaraee - 23-02-2024
Update....
The process stopped by itself with these errors in the picture.
I tried to restart the process just to verify if it is possible to communicate with 63.
The result was no.
Do you think it is still possible to flash it with MOST?
RE: Cic update on E series - bmchicago - 23-02-2024
(23-02-2024, 12:08 PM)zero9 Wrote: Cic does not fail
even on 2009 E9x??? I've been doing it wrong for so long then!
RE: Cic update on E series - DNK76 - 23-02-2024
I made a mistake programming the CIC,
I used ICOM A1 with a bridge adapter,
WINKFPT,
I just forgot to change the interface in EDIABAS
to port 6802
63 - went for CAN
62- went for CAN
A0- I also started programming using CAN for 50 minutes, only 2% progress, I stopped, changed to port 6802 and reprogrammed again, I didn't even have to use expert mode,
when you program again and it stops at the same moment of programming, check the disk, if it is missing or damaged, it always stops programming at the same moment,
RE: Cic update on E series - BimmerSLO - 23-02-2024
you can flash 63, 62 and A0 with MOST. Did many units like this with ICOM NEXT with ICOM NEXT B adapter. Dr GINI settings REMOTE/MOST