[tste1982]

Hi,

i tried flashing my cic but i get the following error:

Fehler: Fehler 4214: Warning COAPIKF.CPP CheckBinDsFilePair 5 Falscher Konvertierungsname C:\EC-APPS\NFS\data\CI62F1\9284325A.0PA 2JQF800A.pbf
Fehler: Fehler 4214: Warning COAPIKF.CPP CheckBinDsFilePair 5 Falscher Konvertierungsname C:\EC-APPS\NFS\data\CI62F1\9284325A.0PA 2JQF800A.pbf
Fehler: Fehler 7903: PABD CI62F1 Programmieren 1570 CCC: HOST-Programmierstatus nicht i.O. für APPL-Programmierung 33CI62F1_10, HOST_PROGRAMMIER_STATUS_LESEN: ERGEBNIS UNGLEICH 1
Fehler: Fehler 7903: Error COAPI2.CPP coapiRunCabd 6 CCC: HOST-Programmierstatus nicht i.O. für APPL-Programmierung SG_PROGRAMMIEREN
Fehler: Fehler 7903: Error COAPIKF.CPP coapiKfProgSgD2 19 CCC: HOST-Programmierstatus nicht i.O. für APPL-Programmierung


does anyone know how to solve this?

i still can connect to the cic with all three cicr files in tool32.

but the cic fan runs at high speed and tool32 shows still flash mode.

can anybody help me?

regards.

[danyro]

Did you try to flash it via obd cable or icom with most?

Sent from my SM-T320 using Tapatalk

---

62 can be done via obd but it works also via most. 63 did work ok? I assume you know the order of flashinc cic - 63 -》 62 -》 A0

Sent from my SM-T320 using Tapatalk

[tste1982]

I tried flashing with icom via most.

63 worked but 62 and a0 did the error.

a0 doesn't show any zusb in inpa.

[danyro]

62 in theory must be done via obd and 63 and a0 with most.
Try with obd(base). I use easykfp to change and lock icom.
I have flashed all ecus from cic with engine running and voltage was aroybd 14,2v.


Sent from my SM-T320 using Tapatalk

[tste1982]

Ok, but the error occurs on 62 and a0. it doesn't matter if i use obd or most.

i flashed with a 60 amp power adapter connected at 14,2 V.

when i open ista-p it shows me programming state 11 and 12 for 62 and a0.
it wants to replace the unit.

does anybody know how to reset the programming state? or delete everything on the flash and start from the beginning?
i saw some options in tool32, but they require an argument, and i don' t know it.

[gbyleveldt]

I had the same issue, start from scratch again with 63, then 62.

All the info is here
http://www.bmwcoding.com/showthread.php?...bricked-GW

[tste1982]

Does anybody know the correct bootloader for the e60?

i got it working again, but now the car icons are gone in pdc or service information. and the hdd seems to be not present, because i don't see any free space when looking at the music storage. navigation doesn't work either.

[tste1982]

So, the hdd is spinning, but it doesn't show up in the navigation or music.

did anyone have also this error? what could it be? i tried reflashing the cic, but still no hdd.

[BaggieMatt]

You might need to do a process ecu/car via NCSexpert. With it being temporarily bricked it have lost what options it has etc.
After updating the software on any ecu I tend to do this.

[tste1982]

I coded it with ncs but it still has the same issues