[m3nt4l]

Hello,

I have removed the air suspension from a 2007 X5 E70 and I’m getting the “ Level Control system failure” message.

Is it just a matter of altering the VO and removing something or is there anything else to it?

If anyone knows full steps that is appreciated.

Thanks

[ZAV]

You should remove from VO option 2VA or 220 and code KOMBI. Use NCS for coding.

[Alwilco]

I've had two scenarios occur on E70's, 1st when Zav's soulution makes the message go away, i.e. SLS is full removed from the E70; 2nd, when the messages still appear. Always try Zav's approach first, if this does not make the message go away, then set SLS timeout in the kombi to not active (nicht_aktiv) and the warning will go away. EHC_APPL_MONITOR.

Hope this helps, Al.

[jadleb]

in order to work need to remove the 3 seat row FA also
because these 2 FA comes together

[m3nt4l]

I've had two scenarios occur on E70's, 1st when Zav's soulution makes the message go away, i.e. SLS is full removed from the E70; 2nd, when the messages still appear. Always try Zav's approach first, if this does not make the message go away, then set SLS timeout in the kombi to not active (nicht_aktiv) and the warning will go away. EHC_APPL_MONITOR.

Hope this helps, Al.

Is this using NCS Dummy?

Thanks

[m3nt4l]

U

I've had two scenarios occur on E70's, 1st when Zav's soulution makes the message go away, i.e. SLS is full removed from the E70; 2nd, when the messages still appear. Always try Zav's approach first, if this does not make the message go away, then set SLS timeout in the kombi to not active (nicht_aktiv) and the warning will go away. EHC_APPL_MONITOR.

Hope this helps, Al.

Hello,

I have changed FA and removed 220 and coded just the Kombi module (sg_codierin) and then when I have checked the .TRC file when reading the Kombi the ehc_Appl_monitor is nicht_aktov. I can’t find the SLS timeout function.

I have still got the error On the dash, any help?

Thanks

[m3nt4l]

U

I've had two scenarios occur on E70's, 1st when Zav's soulution makes the message go away, i.e. SLS is full removed from the E70; 2nd, when the messages still appear. Always try Zav's approach first, if this does not make the message go away, then set SLS timeout in the kombi to not active (nicht_aktiv) and the warning will go away. EHC_APPL_MONITOR.

Hope this helps, Al.

Hello,

I have changed FA and removed 220 and coded just the Kombi module (sg_codierin) and then when I have checked the .TRC file when reading the Kombi the ehc_Appl_monitor is nicht_aktov. I can’t find the SLS timeout function.

I have still got the error On the dash, any help?

Thanks

Update:

I tried clearing fault codes with Carly (was using Launch before) and the error has gone and doesn’t come back even after turning the ignition off etc. But when I scan it with my launch it comes back up? I’ve cleared it with Carly again and hopefully won’t come back. 

Thank you everyone for your help

---

O

U

I've had two scenarios occur on E70's, 1st when Zav's soulution makes the message go away, i.e. SLS is full removed from the E70; 2nd, when the messages still appear. Always try Zav's approach first, if this does not make the message go away, then set SLS timeout in the kombi to not active (nicht_aktiv) and the warning will go away. EHC_APPL_MONITOR.

Hope this helps, Al.

Hello,

I have changed FA and removed 220 and coded just the Kombi module (sg_codierin) and then when I have checked the .TRC file when reading the Kombi the ehc_Appl_monitor is nicht_aktov. I can’t find the SLS timeout function.

I have still got the error On the dash, any help?

Thanks

Update:

I tried clearing fault codes with Carly (was using Launch before) and the error has gone and doesn’t come back even after turning the ignition off etc. But when I scan it with my launch it comes back up? I’ve cleared it with Carly again and hopefully won’t come back. 

Thank you everyone for your help

error came back but realised I hadn't disconnected the module!!


All sorted and no error on dash/iDrive!