Unfortunately we do not accept new members for free, Now яёgїsтядтїои cost 30€, if you are interesting Send Email to [email protected]
Help with evo bricked
|
16-09-2025, 11:29 AM,
(This post was last modified: 16-09-2025, 12:43 PM by HU_man.)
Post: #1
|
|||
|
|||
|
Help with evo bricked
Hello guy,
I cleared V850 (3558) then flashed evo id4 to id6 but failed at btld рдят. Tried it second time still nil help. Now evo bricked (can not see) on ё5у5 anymore to reflash. I have vvdi, v850 adapter, emmc tool, i wrote another evo id4 Dflash (same hw2.3 b142) to it but still bricked. What was i wrong or missed ? Eeprom M95640 need to blank (FF) too ? Can you give me some idea to rescue it ? Thank you so much. EVO ID4/5/6 dumps: EVO dump and EMMC !!! & f5с
MG1 (BDC3): remote start 1CR active remotely MDG1 pre 06/20 OBD циLoск: send me 8Mb flash file All MDG1 Clone, confirm engine start OK: send me 8Mb flash file, 512kb/768kb Eeprom files |
|||
|
|
16-09-2025, 13:16 PM,
Post: #2
|
|||
|
|||
|
RE: Help with evo bricked
Hello,
I've experienced this before. You can try wiping v850 again and performing a NAND repair using the _DEV_UDS.prg. After that, you can try flashing the BTLD using UDS. This will take a very long time, but it worked for me. If that doesn't work via ENET, you can still try it via Passthru. Unfortunately, I don't have a better solution for you. Good luck! |
|||
| Reputation: +2 - al70 [+1] , HU_man [+1] | |||
|
|
![[+]](https://cartechnology.co.uk/images/CarTechnologyTheCure/collapse_collapsed.png)
|
16-09-2025, 13:39 PM,
Post: #3
|
|||
|
|||
|
RE: Help with evo bricked
id4-6, not need cleare V850
|
|||
|
|
|
16-09-2025, 14:06 PM,
Post: #4
|
|||
|
|||
RE: Help with evo bricked
(16-09-2025, 11:29 AM)HU_man Wrote: Hello guy,Did you flash the dump to EMMC? Or just to the V850? You need to upload the dump to emmc !!!Remote OBD MGU Virgin and Custom f5с id 7 id8!!!
5ёяvїcё NCD 2.0, KDS,Secoc, Debug Token EVO EntryEvo Remote Reset EGS Kafas 4 Virgin Whatsapp +48793094471 If I help press rep and THX  |
|||
|
|
|
16-09-2025, 16:00 PM,
Post: #5
|
|||
|
|||
|
RE: Help with evo bricked
Flashing the host is usually necessary to write V850 data and EMMC 8G small board data. You can start the computer after writing these two numbers.
ID4-ID6 is best to brush version 18-3 |
|||
|
|
|
16-09-2025, 21:02 PM,
Post: #6
|
|||
|
|||
|
RE: Help with evo bricked
Same here after any changes in adjust block with SSH
unit are bricked, and now not have SSH access in 169.254.199.119 OMAP I only have access in SSH 169.254.199.99 Jacinto Any idea for fїж this? Please, Press the Buttons
![[їшяgё: postbit_thx.gif]](https://cartechnology.co.uk/images/CarTechnologyTheCure/english/postbit_thx.gif) and ![[їшяgё: postbit_reputation.gif]](https://cartechnology.co.uk/images/CarTechnologyTheCure/english/postbit_reputation.gif) if This post help or is usefull for you! Not is needed write just only thanks in Threads  |
|||
|
|
|
17-09-2025, 00:33 AM,
Post: #7
|
|||
|
|||
|
RE: Help with evo bricked
If you don't have any connection to ё_5у5? I use a Passthru connection in this case from unit directly to ё_5у5. If you use a openport, don't forget to use a 120 Ohm between can-lines to activate the device on bench.
|
|||
|
|
|
17-09-2025, 05:55 AM,
Post: #8
|
|||
|
|||
RE: Help with evo bricked
(16-09-2025, 21:02 PM)ruben_17non Wrote: Same here after any changes in adjust block with SSH Revert adjust block to oem first? COMBOX convert BN2010->BN2000
MGU ратсн EVO repair, f5с ратсн KAFAS4/MRR/RAM virgin |
|||
|
|
|
17-09-2025, 06:15 AM,
Post: #9
|
|||
|
|||
RE: Help with evo bricked
(17-09-2025, 05:55 AM)evaldazj Wrote:(16-09-2025, 21:02 PM)ruben_17non Wrote: Same here after any changes in adjust block with SSH I have copy of original adjust block but is possible restore from 169.254.199.99 jacinto?? Please, Press the Buttons
and if This post help or is usefull for you! Not is needed write just only thanks in Threads |
|||
|
|
|
17-09-2025, 12:28 PM,
(This post was last modified: 08-03-2026, 14:18 PM by HU_man.)
Post: #10
|
|||
|
|||
|
RE: Help with evo bricked
I have only 1 emmc dump same hw2.3 but different HB, safe to write it to emmc ?
Thank you. EVO ID4/5/6 dumps: EVO dump and EMMC !!! & f5с
MG1 (BDC3): remote start 1CR active remotely MDG1 pre 06/20 OBD циLoск: send me 8Mb flash file All MDG1 Clone, confirm engine start OK: send me 8Mb flash file, 512kb/768kb Eeprom files |
|||
|
|
|
« Next Oldest | Next Newest »
|
| Possibly Related Threads… | |||||
| Thread | Author | Replies | Views | Last Post | |
| NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover? | Asp1DD | 8 | 545 |
21-09-2026, 05:05 AM Last Post: flashxcode |
|
| Revive Bricked CIC | malone0185 | 7 | 426 |
13-08-2026, 14:58 PM Last Post: malone0185 |
|
| Ms43 - Bricked or Recovery | IDOT | 1 | 115 |
16-04-2026, 07:02 AM Last Post: Buszkin |
|
| help with bricked NBTEVO HW2.3 | Cro | 4 | 303 |
06-04-2026, 06:27 AM Last Post: Cro |
|
| Files for bricked nbt evo | Ryn079 | 0 | 176 |
23-03-2026, 19:13 PM Last Post: Ryn079 |
|
| BRICKED NBT EVO HW2.3-HELP | grizzle | 7 | 920 |
19-03-2026, 11:55 AM Last Post: Cro |
|
| NBT EVO ID4 bricked | Albert-M | 5 | 457 |
18-03-2026, 18:56 PM Last Post: Albert-M |
|
| NBT EVO bricked | szefuncio512 | 29 | 1,597 |
26-02-2026, 10:54 AM Last Post: szefuncio512 |
|
| Solved ✔ MS45 bricked by i5тд/P | tonemoz | 6 | 283 |
23-09-2025, 18:08 PM Last Post: tonemoz |
|
| Solved ✔ Cas4 bricked after i5тд update F25 | m4rrtin | 6 | 292 |
09-07-2025, 06:59 AM Last Post: m4rrtin |
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content
