[rad]

same here,ETKA not found..Win7 x64

[Raymi]

NOT Working!!!

[ridamavu]

Guys,
This is the first time that I'm tring to install ETKA. I have a working setup of ELSAWin on my VM.
The OS is Win7 32bit.

I installed it, as shown on the first post but I get a "PATH not found" error. Also the updater is showing a dead link.

Can someone tell me what is the easiest OS to use and the right procedure to install and update it?
The machine should be connected to internet or not?
Thanks!

No one?
Really? Starting to think that I'm loosing my time with this shit software.

I tried again with another fresh install but I'm still getting the same ERROR. So I think that the problem is due to the software and not the machine itself.

The installer sometimes doesent even make the desktop links...

NO DDL errors or something strange just the path not found. The software is installed on the C drive.

[Kees B]

password Winrar

See post #1, you have to ask via PM.

---

---

For anyone who had already tried to update to ETKA 8.1 and can't finish the setup, here is a possible solution.



!!! Before you start please make a backup of you ETKA Folder !!

1. Prerequisite:  The folder "C:\ETKA\PROG\IX\" is available in your ETKA Folder.

2. Copy the contents of the folder "C:\ETKA\PROG\IX\PROG\"   to   "C:\ETKA\PROG1\" and overwrite the existing files.

3. Copy the contents of the folder "C:\ETKA\PROG\IX\DATA\"   to   "C:\ETKA\DATA\" and overwrite the existing files.

Now ETKA 8.1 should start without any problem. Maybe the solution for missing user data has to be done now.

Good Luck,
Planet-Fireball

Thanks! Followed the instructions but still ETKA on my laptop (W10 32-bits) does not update to 8.1, with the same error message (no ETKA 8 found). Any further suggestion would be much appreciated.

EDIT: Update to 8.1 successful! Not sure how it happened exactly but after following the above instructions and still getting the "no Etka8 found" error I re-ran the update exe from Etka 7.5 to 8 which was saved in my back-up files, but I did cancel the final installation step for fear of corrupting the program. Low and behold, after restarting Etka it appeared to be the updated version 8.1. 

I then ran into the issue mentioned in Post #121 (User Identification / Login Data) and fixed that with Planet-Fireball's instructions. Many thanks for that again!

All is well for now - I hope it may be of some help to those of us who face the same issue.

[lokfahrer]

You have a link to the UpdateThread when installing the ::..LexCom..:: version on the Desktop! Follow this and load the file ETK80-1239-765-771-1239-ETK81. After running you can run the exe!

Where can i find this update (ETK80-1239-765-771-1239-ETK81) ?

[onoff]

---

---

EDIT: Update to 8.1 successful! Not sure how it happened exactly but after following the above instructions and still getting the "no Etka8 found" error I re-ran the update exe from Etka 7.5 to 8 which was saved in my back-up files, but I did cancel the final installation step for fear of corrupting the program. Low and behold, after restarting Etka it appeared to be the updated version 8.1. 



can you share this ??

I re-ran the update exe from Etka 7.5 to 8 which was saved in my back-up

[911Turbo]

Here is the update folder for V7.5 to V8.0 in case it helps anyone

[rad]

also not working....

[planet-fireball]

Data Updates
There are many PM Requests about the latest Updates.
The reason of the empty uploaded.to folder after the installation is, 
that carfreak.kiss (the creator of this ETKA version) has stopped
supporting ETKA.

So please use the well known ETKA update software, which can also
be found on this forum.


ETKA Updates (from 8.0 to 8.1)
There is no 100% working update solution at the moment, which 
works on all computers and operating systems. A variant which has
already led to success on several computers, I have presented in my
last post. Without warranty of function or completeness.


Leechers
There are currently too many leecher requests, conspicuous with the
same content in the PMs. I will now examine the requests more closely.
Therefore, the answers on the PMs takes a little longer.

And please make sure you have the "PM Receiving" function turned on in your profile settings. 
I'm getting tired on the "The user has turned off PM Receiving" message. 

[donjuan020]

ETKA ERROR "PATH NOT FOUND" HOW TO SOLUTION? THANK YOU.
BEST REGARDS.