Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Mini F56 Seat belt light
29-01-2019, 09:11 AM,
Post: #1
|
|||
|
|||
Mini F56 Seat belt light
Hi Mates,
I have problem with F56 Mini 2015. There is seatbelt light on and fault code in kombi: -KOMB25 0xE114A3 Message (status, seat belt buckle contact, seat occupancy, 0x297) checksum error, receiver KOMBI, transmitter ACSM ACSM is without fault code. Wehicle was allready falshed and ACSM was replaced and it is the same. Thanks |
|||
30-01-2019, 06:07 AM,
Post: #2
|
|||
|
|||
RE: Mini F56 Seat belt light
"checksum error " mean there wrong with something programming part
|
|||
30-01-2019, 13:19 PM,
Post: #3
|
|||
|
|||
RE: Mini F56 Seat belt light
Try running through a session with ISTA-P and see if that agrees you have the correct software version on the ACSM, and recode things if you haven't tried that.
If it is the wrong module or software, you should see a message to replace or update the ACSM |
|||
01-06-2019, 18:12 PM,
Post: #4
|
|||
|
|||
RE: Mini F56 Seat belt light
Hello
I have the same problem. Did you solve it? |
|||
01-06-2019, 21:24 PM,
Post: #5
|
|||
|
|||
RE: Mini F56 Seat belt light
Did you flash ACSM ?
|
|||
02-06-2019, 04:49 AM,
(This post was last modified: 02-06-2019, 06:01 AM by Terabyte.)
Post: #6
|
|||
|
|||
RE: Mini F56 Seat belt light
Yes I flashed whole car with newest psdzdata
I just tried to make new flash of ACSM, but it abortet. And now I don't get connection to ACSM anymore ACSM negative response error: Timeout |
|||
10-07-2019, 08:59 AM,
Post: #7
|
|||
|
|||
RE: Mini F56 Seat belt light
(29-01-2019, 09:11 AM)kuks Wrote: Hi Mates, Unfortunately I have the same problem.. no error in ACSM, I used ACSM4i in tool32: first I run fs_lesen, and fs_loeschen then is_lesen and is_loeschen finally steuergeraete_reset I've tried also the job STEUERN in custom (ARG;VERRIEGELUNG_SG;0) but when I select "0" it gives me error. What can I do? Thanks.. |
|||
11-07-2019, 08:34 AM,
Post: #8
|
|||
|
|||
RE: Mini F56 Seat belt light
Here the tool32 logs:
I N F O R M A T I O N M E M O R Y --------------------------------------- Date: 10.07.2019, 20:37:03 JobStatus: OKAY Variant: ACSM4I.PRG Version: 6.500 ------------------------------------------------------------- RESULT: 1 error in error memory ! ------------------------------------------------------------- 0x01A062 DEM_INT_AECU_ASYNCHRON_MODE Error counter : 1 Healing counter : 255 Absolute time 159379818 s Mileage 33984 km BETRIEBSSTUNDENZAEHLER_BEGINN 9770833.00 s BETRIEBSSTUNDENZAEHLER_ENDE 9770838.00 s AUSSENTEMPERATUR 29.00 °C SG_INNENTEMPERATUR -0.10 °C SYSTEMZUSTAND_PDC: ungueltig 1.500000E+001 0-n SYSTEMZUSTAND_KLR: KL R ein 1.600000E+001 0-n SYSTEMZUSTAND_KL_R_W: Wechsel erfolgt 2.560000E+002 0-n SYSTEMZUSTAND_KL_15: KL 15 ein 4.096000E+003 0-n SYSTEMZUSTAND_KL_15_W: KL 15 Wechsel erfolgt 6.553600E+004 0-n SYSTEMZUSTAND_MOT: kein Motorstart 0.000000E+000 0-n SYSTEMZUSTAND_GESCHW: ungültig 2.516582E+008 0-n ZEIT_NACH_PWRON 19.00 s POWER_ON_ZAEHLER 12529.00 count SG_SPANNUNG 12194.00 mV Testbedingungen erfüllt Fehler momentan nicht vorhanden, aber bereits gespeichert Fehler würde kein Aufleuchten einer Warnlampe verursachen This is no event DTC. This ecu IS RESPONSIBLE for this error entry. Error code: 00 01 A0 62 2C 01 17 00 01 48 10 17 01 09 7F F1 6A 40 00 00 95 17 51 40 01 00 95 17 56 40 02 00 8A 40 03 FF FF 40 04 0F 01 11 1F 40 05 00 13 40 06 00 00 30 F1 40 07 2F A2 01 00 02 01 03 FF ============================================================= apiJob("ACSM4I","steuern","ARG;VERRIEGELUNG_SG;0","") Satz : 0 OBJECT = acsm4i SAETZE = 1 JOBNAME = steuern VARIANTE = ACSM4I JOBSTATUS = UBATTCURRENT = -1 UBATTHISTORY = -1 IGNITIONCURRENT = -1 IGNITIONHISTORY = -1 Satz : 1 JOB_STATUS = ERROR_ECU_CONDITIONS_NOT_CORRECT _REQUEST = 4 Bytes 0000 : 2E D4 82 00 .Ô?. _RESPONSE = 3 Bytes 0000 : 7F 2E 22 ." |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content