Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
22-01-2023, 12:54 PM,
(This post was last modified: 22-01-2023, 12:55 PM by tvrdas.)
Post: #11
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
(22-01-2023, 12:37 PM)r0my81 Wrote: I tryed today your solution but no way. Tried two times. Second one I did fresh install Odis 10 from justdiag delete/swap files you share in this topic and then launch Odis... There is no ignition/battery value and there is a little window at the right bottom that suggest me a VCI Firmware Update! I tried yesterday this solution. First program run it wants to update and freeze but after restart and run again it worked well. ODIS S10 |
|||
22-01-2023, 14:09 PM,
(This post was last modified: 22-01-2023, 14:49 PM by isdochegal.)
Post: #12
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
(22-01-2023, 12:37 PM)r0my81 Wrote: I tryed today your solution but no way. Tried two times. Second one I did fresh install Odis 10 from justdiag delete/swap files you share in this topic and then launch Odis... There is no ignition/battery value and there is a little window at the right bottom that suggest me a VCI Firmware Update! If the VAS6154 folder had been deleted first before copying the files, no FW update could be suggested. And of course the latest FW update with SVCI Device Manager must first be installed on the SVCI 6154A! ==> look the attachement If you like my post and it helped you, please press +
|
|||
22-01-2023, 14:55 PM,
Post: #13
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
HI can i do the same with my clone can it warks with this solution?
I have this clone. |
|||
22-01-2023, 15:39 PM,
Post: #14
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
No! This works only with the SVCI.
If you like my post and it helped you, please press +
|
|||
Reputation: +1 - billyleon [+1] | |||
23-01-2023, 07:29 AM,
Post: #15
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
thanks mate for your help , so far just waiting for my activation of odis- s 10 to go further and test your solution
|
|||
23-01-2023, 19:22 PM,
Post: #16
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
well mate excuse me , i have lot of question since i didn't install odis higher than ver 7.1 yet, so this is my 1st with ver 10 , when i uninstalled 7 and installed odis s 10 , i can't find folders u said to replace .u mind more guiding ?
|
|||
24-01-2023, 08:39 AM,
(This post was last modified: 24-01-2023, 12:08 PM by isdochegal.)
Post: #17
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
You are looking in the wrong folder! On your picture you are looking in "C/ProgramData" but the driver is located in "C/Program Files". In any case, it can be found there with OS10 + 11 and OE15 + 16. In older versions, this was found elsewhere.
If you like my post and it helped you, please press +
|
|||
25-01-2023, 20:28 PM,
Post: #18
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
Thanks for your advice, I tryed again and works. First time Odis seems like trying to update VCI so close program/reboot and launch Odis again. I tryed on transporter 2018 Dignose/readding some values.
|
|||
26-01-2023, 10:21 AM,
(This post was last modified: 26-01-2023, 10:22 AM by billyleon.)
Post: #19
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
(22-01-2023, 14:55 PM)billyleon Wrote: HI can i do the same with my clone can it warks with this solution? Its possible some solutions for my clone? Some moded drivers? |
|||
31-01-2023, 08:40 AM,
Post: #20
|
|||
|
|||
RE: Possible solution to use the yellow SVCI 6154A with ODIS-S 10/11 and ODIS-E 15/16
Hello, I have the SVCI, with which I had problems to identify the ABS module, I identified it when I wanted, however I bought one of those PASSTRHU, and since then no problem, the only thing I have tried to flash has been some TPMS parameters created by me... and very well.
MORKAS
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
volthex, 2 Guest(s)
volthex, 2 Guest(s)
Return to TopReturn to Content