[ccfj1]

As requested.

Needed for the bench setup, you can get away without the elv if you have the correct CAS (or the correct version of firmware), but i cant confirm this yet.

1: Cas (c4),
2: Key (for above cas)
3: key holder and ribbon lead
4: Start/stop button.
5: elv
6: kombi (cluster)
7: Power source for 12v.

I use connector blocks so that I can have mulitple taps for each GND, +12v, Wakeup (12v ign) and High/Low bus.

OBD II
1: Ignition Connector Block (wakeup)
2: not connected
3: Ethernet connection to cic quadlock pin 37 (black plug)
4: Gnd Connector Block
5: Gnd Connector Block
6: K-bus high (pin 17 on blue 54 pin jbr plug, x14271)
7: I have this connected to pin 30 (PA-BUS) of the CAS (not sure if this is correct???
8: Ethernet connection to cic quadlock pin 29 (black plug)
9: F_TD this goes to the DME)
10: not connected
11: Ethernet connection to cic quadlock pin 38 (black plug)
12: Ethernet connection to cic quadlock pin 31 (black plug)
13: Ethernet connection to cic quadlock pin 32 (black plug)
14: K-bus low (pin 33 on blue 54 pin jbr plug, x14271)
15: not connected
16: +12v Batt Connector Block

JBR x14270 ( the long black plug)
Pin 23 <----- GND Connector Block

JBR x14271 (the 54pin blue plug)
JBR x14271 Pin 10 = K-bus low <----> CAS X13376 pin 26 = K-bus low
JBR x14271 Pin 46 = K-bus high <----> CAS X13376 pin 35 = K-bus high

Pin 17 K-bus high <----> OBD Pin 6
Pin 33 K-bus low <----> OBD Pin 14

Pin 45 wakeup <----> (ignition) also connected to Pin 1 OBD

JBR x14272 (the 54pin black plug) to 8 pin CID (black cic display plug)
+12v -----> Power to Controller Pin 1
GND -----> GND to Controller Pin 2
Pin 11 <----> K-bus high CID Pin 3
Pin 30 <----> K-bus low CID Pin 4

Pin 1 -----> Power to CID Pin 1
Pin 27 -----> GND to CID Pin 3
Pin 29 <----> K-bus high CID Pin 5
Pin 31 <----> K-bus low CID Pin 6

JBR x4010 23pin plug (that connected to the fusebox base)
Pin 3 <----- +12v Batt (source) Connector Block
Pin 22 <----- +12v Batt (source) Connector Block

CAS X13376 black 41pin plug
Pin 21 <----- +12v Batt Connector Block
Pin 34 <----- +12v Batt Connector Block

Pin 12 <----> GND Connector Block
Pin 25 <----> GND Connector Block

Pin 8 <----> wakeup (ignition)
Pin 26 <----> K-bus low
Pin 35 <----> K-bus high

ELV
Pin 1 <----> GND Connector Block
Pin 2 <----> CAS EL + pin 23 CAS
Pin 3 <----> CAS EL - pin 24 CAS
Pin 4 <----> CAS PA-bus pin 30 CAS

Kombi
Pin 18 <----- GND Connector Block
Pin 9 <----- Power Connector Block
Pin 7 <----> K-bus low Connector Block
Pin 6 <----> K-bus high Connector Block

--