RE: Bmw e53 3.0d (2003) ECU update probleme need help
(04-06-2022, 18:56 PM)P_hex Wrote: (04-06-2022, 17:28 PM)hero3838 Wrote: The problem then followed, the
car then a 2003 BMW E53 3.0D , the original plan was to upgrade the DME but winkfp failed to load even when it was thrown for the first time errori:
Error 211:
Error on flash programming!
Code
2021 datatransmission to ECU disrupted IFH-0010 datatransmission to ECU disrupted 12DDE40
2021 datatransmission to ECU disrupted SG_PROGRAMMIEREN
2021 datatransmission to ECU disrupted
and another
Error 211:
Error on flash programming!
Code
2020 no response from ECU ..... etc
After that, the car will not start, says "fuel injection system" (does not take the feed pump), "trans. file safe prog '' (box in emergency mode), temp immediately below when the ignition is switched on and the ASC light illuminates with ABS. The above error did not exist before ....
The engine cannot be accessed with INPA (SYS-0012 IDENTIFICATION ERROR), but the box, IKE, KMBI, etc. can be accessed. The error code in these modules is "Error CAN-bus timeout DME" (ie the modules cannot connect to the brain)
Tool32 and WinKfp get some access, for example the UIF can be read, and so
In the case of a normal K + DCAN cable with pins 7 and 8 twisted together, I also tried to disconnect the same result. İ have icom but i can't connect icom to inpa,ista or winkfp not car related problem i think ebidas ini problem.
İ attached photo; coding data and zbs before flashing, flash error photo, ECU photo, inpa ECU information before flash error
is anyone exposed to similar problems? Got a dump here and program flash memory - 0281010314 7789376 1037351761
Thanks for your kind response
Which tool can i use programing for flash memory
(05-06-2022, 09:27 AM)Cowboy Wrote: If it is DDE4, it is an ECU which very often causes problems during programming. I had a similar case a few years ago, except that the ECU died while programming with ISTA. Everything was fixed with DIS 44. DIS includes ECU repair functions.
Thanks
Did you use k+dcan cable for repair with dis 44
(05-06-2022, 09:33 AM)hero3838 Wrote: (04-06-2022, 18:56 PM)P_hex Wrote: (04-06-2022, 17:28 PM)hero3838 Wrote: The problem then followed, the
car then a 2003 BMW E53 3.0D , the original plan was to upgrade the DME but winkfp failed to load even when it was thrown for the first time errori:
Error 211:
Error on flash programming!
Code
2021 datatransmission to ECU disrupted IFH-0010 datatransmission to ECU disrupted 12DDE40
2021 datatransmission to ECU disrupted SG_PROGRAMMIEREN
2021 datatransmission to ECU disrupted
and another
Error 211:
Error on flash programming!
Code
2020 no response from ECU ..... etc
After that, the car will not start, says "fuel injection system" (does not take the feed pump), "trans. file safe prog '' (box in emergency mode), temp immediately below when the ignition is switched on and the ASC light illuminates with ABS. The above error did not exist before ....
The engine cannot be accessed with INPA (SYS-0012 IDENTIFICATION ERROR), but the box, IKE, KMBI, etc. can be accessed. The error code in these modules is "Error CAN-bus timeout DME" (ie the modules cannot connect to the brain)
Tool32 and WinKfp get some access, for example the UIF can be read, and so
In the case of a normal K + DCAN cable with pins 7 and 8 twisted together, I also tried to disconnect the same result. İ have icom but i can't connect icom to inpa,ista or winkfp not car related problem i think ebidas ini problem.
İ attached photo; coding data and zbs before flashing, flash error photo, ECU photo, inpa ECU information before flash error
is anyone exposed to similar problems? Got a dump here and program flash memory - 0281010314 7789376 1037351761
Thanks for your kind response
Which tool can i use programing for flash memory
(05-06-2022, 09:27 AM)Cowboy Wrote: If it is DDE4, it is an ECU which very often causes problems during programming. I had a similar case a few years ago, except that the ECU died while programming with ISTA. Everything was fixed with DIS 44. DIS includes ECU repair functions.
Thanks
Did you use k+dcan cable for repair with dis 44
DISis: Coding / Programing-Programming-DDE programining-replace unit-Faulty unit stil connected: Yes .... This function is it
İf not can you explain more specifically i don't use dis very long time and not familiar with it much
|