[bohozoku]

If you compare 522 vs 552 there are more wiring differences ?

[bmw335coding]

UPDATE: It was an simple fault.
PIN3 at both headlights are before from Xenon Lights TFL_L + TFL_R and with LED there is Klemme30_f.
After fix this both TMS are visible.

[XALLECS]

I am reading your last post for about 30 min and try to understand what you say
1. afther retrofit on PIN3 i have from the fem the 30 klemme
2. on 8 there is lin bus

what exchange i have to do for it ?
i think i will lose my mind with this ..........

[bmw335coding]

I am reading your last post for about 30 min and try to understand what you say
1. afther retrofit on PIN3 i have from the fem the 30 klemme
2. on 8 there is lin bus

what exchange i have to do for it ?
i think i will lose my mind with this ..........

Short for you:

Give PIN3 on both sides KLEMME_30F.

[dzik1981]

Hello
I had a similar communication problem
if the wiring is ok !?
I do not remember exactly what I did but it was about coding
replace esys 552 to 5A2 (nini F56 led lamp)
then make ista start the LED lamps
after running, replace 5A2 with 552

[BigNode]

Solution...
1. When you completed the manual work remember to NOT INSTALL THE LED HEADLIGHT BEFORE HAVE CODED FA (Veichle Order) AND FRM ECU.
This step is FUNDAMENTAL, because FRM send different signals to headlights depending of the configuration, if you install LED but the car and FRM is coded for xenon simply you risk to burn your LED headlight
2. BEFORE plug the wiring connector the led headlights, code your car FA (for the F series you have to insert S552 options and delete S524 (adaptive headlights), however check your VO configuration to be sure).
Use Esys to code FA and then VO code the FRM.
3. Now you can plug the wiring connectors.
Turn ignition on and.....these headlights don't work
What happened?
4. Take it easy, the headlights remains completely off until you don't program (flash) and code their four ECU.
Turn on Esys, flash and VO code the headlight ecu (two for each headlight, LHM and TMS if i well remind...).
Now your headlight turn on, but it still don't work correctley.....(no turn signal, no adaptive, ecc.).
5. Finally turn on ISTA-D,follow the calculate plan procedure to start the "auto-learning" procedure (about 30 seconds).
At the end, make a new car diagnostic, erase all fault memory.
Happy end
dont forget +tnx & rep...

[williammm]

Can F30 with Xenon Headlight be retrofitted with Adaptive LED Headlights?
Just need the headlight alone?

[bmw335coding]

Can F30 with Xenon Headlight be retrofitted with Adaptive LED Headlights?
Just need the headlight alone?

Why not? You see i do it.

[williammm]

Can F30 with Xenon Headlight be retrofitted with Adaptive LED Headlights?
Just need the headlight alone?

Why not? You see i do it.

Just the Headlight alone? Do i need the Kafas?
I just retrofitted to LCI LED Headlight.

[kubixix]

Hello,
I also want to retrofit but i have adaptive xenons(522 and 524).
From what I know I should bridge like 335coding:
PIN 9 and PIN 11
PIN 10 and PIN12
That will be the part of K-CAN2 to both TMS and LHM( not just a TMS like in adaptive xenons)

Everything seems okay apart from PIN3 which currently is connected wrong(should i disconnect it)? Don't know how to connect to like you said KLEMME_30, because ista says its connects to "Supply terminal,30 FUSE 40", I see this FUSE is in front power distribution box. Where should I connect this PIN3 to get it working? Just connect it to:
Z7*10B in front distribution box?(i'm talking about left light).


Thanks