[ROD-BENDERS]

Hello
I need an off DTC P2453
Opel Astra J 2.0 160HP MODEL 2011
EDC17C18
Thank you

Hi mate, my DTC remover does not support this ECU.

I ran it through my DPF soft and DTC's were deleted.

---

Hello, I have audi a4 2007 2,7 diesel with EDC17 please remove dtc P3135 and P1018 THX

Hi Mate

Please give full ecu details in future, ok.

solution is based on your ecu being EDC16U34

Flaps Off csok

Please disconnect diff sensor + exhaust temp sensor or go into limp mode. If it does not work then I am unable to help you further with this ecu.

---

Hi Buzzard you can remove error P02E0 and P02E1 from edc16c39 of opel antara 110kw?
Thanks in advance
Best Regards

Hi mate, my soft cannot find the file structures, sorry.

[MIKAS]

Hello,

you can do DPF off ssangyong rexton 270 xdi ecu DCM 3.2 ?

Thank you for your help

here the file

Regards Mikas

[ROD-BENDERS]

Hello,

you can do DPF off ssangyong rexton 270 xdi ecu DCM 3.2 ?

Thank you for your help

here the file

Regards Mikas

Sorry Mikas

Ssangyong not supported mate.

[nedved59]

Hi , i need egr off audi a3 edc16u34
best regards

[ROD-BENDERS]

Hi , i need egr off audi a3 edc16u34
best regards

There you are Nedved egr is off mate

[blokers77]

Hi Buzzard
Can you help me with this car?:
Mercedes ML163 2.7cdi
BOSCH 0281010283 EDC15C6

I need - swirl flaps + P1189 - OFF


Thanks for help mate!

[Blacksmoke]

Hi

Can you delete DPF on the attached file please? It is for 2010 VW Polo 1.6TDI CR with Siemens PCR2.1 Ecu. It was read with a KESS tool.

Thanks in advance

[ROD-BENDERS]

Hi Buzzard
Can you help me with this car?:
Mercedes ML163 2.7cdi
BOSCH 0281010283 EDC15C6

I need - swirl flaps + P1189 - OFF


Thanks for help mate!

Hi Blokers

Your file is not showing the dtc's table with my software so I cannot do dtc off, and my flap remover only covers newer ecu's of EDC16 +

Only other option I can find out there, apart from fixing the car , is that some folks are removing flaps and plugging the spindle holes in some way. Then evidently, this mod stops the dtc's coming, Its not tested by me, but it may give you ideas on how you want to proceed. "To avoid logging fault codes, is wire in a resistor between the signal (PWM) wire and the 12v wire to the M55 motor.I have found that values from 1k to 10k ohms work - 20k ohms is too high".

---

Hi

Can you delete DPF on the attached file please? It is for 2010 VW Polo 1.6TDI CR with Siemens PCR2.1 Ecu. It was read with a KESS tool.

Thanks in advance

Hi Blacksmoke

I hope this fixes your dpf mate

No checksum !

[Blacksmoke]

Hi Buzzard
Can you help me with this car?:
Mercedes ML163 2.7cdi
BOSCH 0281010283 EDC15C6

I need - swirl flaps + P1189 - OFF


Thanks for help mate!

Hi Blokers

Your file is not showing the dtc's table with my software so I cannot do dtc off, and my flap remover only covers newer ecu's of EDC16 +

Only other option I can find out there, apart from fixing the car , is that some folks are removing flaps and plugging the spindle holes in some way. Then evidently, this mod stops the dtc's coming, Its not tested by me, but it may give you ideas on how you want to proceed. "To avoid logging fault codes, is wire in a resistor between the signal (PWM) wire and the 12v wire to the M55 motor.I have found that values from 1k to 10k ohms work - 20k ohms is too high".

---

Hi

Can you delete DPF on the attached file please? It is for 2010 VW Polo 1.6TDI CR with Siemens PCR2.1 Ecu. It was read with a KESS tool.

Thanks in advance

Hi Blacksmoke

I hope this fixes your dpf mate

Hi

Will feedback once tested. Thanks again

[advanced]

Hi Buzzard
please i need dtc off for PSA peugeot Partner EDC17C10 P0402 P1434 P1435 P0460