Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Coding G-series, beginners guide?
23-01-2018, 11:05 AM,
(This post was last modified: 23-01-2018, 11:06 AM by jaki.)
Post: #1
|
|||
|
|||
Coding G-series, beginners guide?
I have coded succesfully several F- series without problems, but today I faced first G-series (G01 X3).
I know that I have chose S15A, but what exatly I have to do? In F- series I can put ignition on, just pushing Start button. Sounds stupid, but how an earth I can put ignition on in G- series? I looks that it switchs only partially when pushing start button. I have read elsewhere that SVT read does not function at all ( ok, it does not), but reading ECUS's resulted only 6 units. I assume it is because of that ignition missing, or what? Should I have some spesific version of Esys to code G- series? I have newest daten in my system, but esys is 3.27. I'm dreaming currently only coding, not flashing. |
|||
23-01-2018, 11:19 AM,
Post: #2
|
|||
|
|||
RE: Coding G-series, beginners guide?
Ignition is switched on on active diagnostic session. So the easiest way is to run diagnostic first, then do coding, otherwise you'll have to use transmitter or tool32 to switch ignition on through bdc.
|
|||
23-01-2018, 11:53 AM,
Post: #3
|
|||
|
|||
RE: Coding G-series, beginners guide?
(23-01-2018, 11:19 AM)lynxbmw Wrote: Ignition is switched on on active diagnostic session. So the easiest way is to run diagnostic first, then do coding, otherwise you'll have to use transmitter or tool32 to switch ignition on through bdc. I realised that running diagnostic with Icom Next + ISta did the job, but I assume connecting with enet is hard after that, at least I couldn't connect. I have to look tool32 option. |
|||
23-01-2018, 11:54 AM,
Post: #4
|
|||
|
|||
RE: Coding G-series, beginners guide?
Hit Start/stop button 3x in 1 second and You have ignition on
|
|||
Reputation: +1 - vitalix [+1] | |||
23-01-2018, 12:33 PM,
(This post was last modified: 23-01-2018, 13:35 PM by jaki.)
Post: #5
|
|||
|
|||
RE: Coding G-series, beginners guide?
|
|||
23-01-2018, 12:40 PM,
Post: #6
|
|||
|
|||
RE: Coding G-series, beginners guide?
[/quote]
I realised that running diagnostic with Icom Next + ISta did the job, but I assume connecting with enet is hard after that, at least I couldn't connect. I have to look tool32 option. [/quote] I had it several times after diagnostic with Icom, connecting with enet is hard after that. What can cause this problem? When I connect the next day to the same car I had no problems with Enet-cable? |
|||
23-01-2018, 15:15 PM,
Post: #7
|
|||
|
|||
RE: Coding G-series, beginners guide?
I always code with engine on unless hooked up to charger.
|
|||
23-01-2018, 22:49 PM,
Post: #8
|
|||
|
|||
RE: Coding G-series, beginners guide?
@jaki you should update Esys to newer version - 3.27 does not work with latest psdz (3.63). Use 3.30.1 or 3.31
Email: [email protected] Skype: [email protected]
HU Engineering Tool MGU Engineering Tool - now with field update mode via Feature Installer. Coding 2.0 |
|||
24-01-2018, 00:23 AM,
(This post was last modified: 24-01-2018, 00:23 AM by Almaretto.)
Post: #9
|
|||
|
|||
RE: Coding G-series, beginners guide?
(23-01-2018, 22:49 PM)pshoey Wrote: @jaki you should update Esys to newer version - 3.27 does not work with latest psdz (3.63). Use 3.30.1 or 3.31 I am still using 3.27.1 with 3.63.3. 3.27.1 is only version external transmitter works for me. 3.31 also has errors with with Coding-Verification. |
|||
24-01-2018, 01:56 AM,
(This post was last modified: 24-01-2018, 01:56 AM by pshoey.)
Post: #10
|
|||
|
|||
RE: Coding G-series, beginners guide?
@almaretto good to know but for me the I-Step dropdowns are grayed out - I seem to remember there was some kind of patch to fix it??
Agree, transmitter is broken in newer ESys versions - I have not tried copying it over from 3.27 to the newer ones - might try that later. Email: [email protected] Skype: [email protected]
HU Engineering Tool MGU Engineering Tool - now with field update mode via Feature Installer. Coding 2.0 |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
using Inpa for f series | hero3838 | 0 | 15 |
3 hours ago Last Post: hero3838 |
|
BMW E71 EGS coding 8HP70 used | BS68 | 4 | 238 |
04-05-2024, 18:08 PM Last Post: Ryzen |
|
F25 5AS,8th and 5AC coding with 6wb kombi | simplextibi | 1 | 70 |
04-05-2024, 06:37 AM Last Post: Stratofortress |
|
dissable RDC on G series ? | xMoses | 6 | 241 |
02-05-2024, 08:48 AM Last Post: Node |
|
BMW F40 (1 series) no FZD module | Ibrahim24 | 5 | 188 |
01-05-2024, 19:27 PM Last Post: Siki78 |
|
Bmw F34 trailer hitch coding ? | Cryjack | 2 | 84 |
27-04-2024, 20:27 PM Last Post: dumitru.o |
|
F20 LCI2 black panel cluster coding | sqorpius | 10 | 2,118 |
27-04-2024, 06:51 AM Last Post: hamzettin |
|
FDL coding BMW Apps | Mugga | 3 | 231 |
26-04-2024, 18:06 PM Last Post: Mugga |
|
Coding a F80 M3 race car | PeterY | 10 | 593 |
25-04-2024, 23:32 PM Last Post: Furgus |
|
NBT Evo CAFD missing after coding error | Mugga | 13 | 666 |
24-04-2024, 22:47 PM Last Post: Mugga |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content