Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
E63 M6 coding over diagbus error coapi 1000
06-09-2018, 21:41 PM,
Post: #1
|
|||
|
|||
![]()
Hello,
today I update the CCC of an E63 M6 to the lastest I-Stufe with ISTPA-P v65 I have a original ICOM with MOST and the programming works fine after few trys on Port 6802. On Port 6801 they abort at the BO and CCC-A ECU. OK this step are solved. But if the coding job starts or I try a full car coding, I get COAPI 1000 error. The same problem in NCSExpert. ISTA+ works finde and the programming with ISTA-P works too...but what is the problem with ecu coding over the Diagbus? |
|||
06-09-2018, 21:52 PM,
(This post was last modified: 06-09-2018, 21:53 PM by inotherwords.)
Post: #2
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
Are you trying to code it using MOST adapter or not? If so, you need to configure EDIABAS to use MOST adapter first. You can do this using EasyConnect utility.
|
|||
07-09-2018, 06:20 AM,
(This post was last modified: 07-09-2018, 06:35 AM by weby.)
Post: #3
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
Ahhh ok...MOST for EDIBAS and then try it again?
But for Ista P normally I dont need this Setup, because they Switch automaticlly. They programming via MOST, but coding are for all ECUs via Diagbus. But all other ecus outside the MOST-Bus arent coded too. |
|||
07-09-2018, 08:57 AM,
Post: #4
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
Actually you can set ICOM to DiagBus or Base, you don't need to use MOST
|
|||
07-09-2018, 20:59 PM,
(This post was last modified: 07-09-2018, 21:08 PM by weby.)
Post: #5
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
And Base instead DiagBus is the right configuration to code?
Then I try it and configure the REMOTE.INI. I use in EDIBAS REMOTE Interface and fix now in my REMOTE.INI the Hosts. At BASE they is "opps_name". I fix it with my static (dhcp assign) IP of my ICOM. Thanks for this info! |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
![]() |
ETK 2020.01 Install issue (transbase error) | huadgal | 0 | 10 |
1 hour ago Last Post: huadgal |
RQ: Help for coding E9X FRM2 DRL with AE | codingbmwsofia | 0 | 25 |
Today, 05:47 AM Last Post: codingbmwsofia |
|
![]() |
F30 Coding flash with fog lights | x3non507 | 2 | 157 |
12-06-2024, 19:45 PM Last Post: grizzle |
F8x NBT Refrofit Flash Failed; Fatal Error Help | mitch32 | 5 | 194 |
10-06-2024, 09:47 AM Last Post: painsage |
|
Entrynav2 Retrofit Ethernet Error | moreply | 1 | 164 |
06-06-2024, 11:35 AM Last Post: moreply |
|
![]() |
Coding a F80 M3 race car | PeterY | 20 | 1,156 |
06-06-2024, 09:39 AM Last Post: ravager |
![]() |
Bmw f30 xdrive disable coding | hero3838 | 5 | 237 |
02-06-2024, 10:54 AM Last Post: hero3838 |
Secure coding in BMWs (unit list) | Node | 88 | 16,042 |
01-06-2024, 02:05 AM Last Post: champuser-riven |
|
![]() |
E39 Rain Light Sensor / Auto Headlight Retrofit Coding | bmw335coding | 1 | 103 |
31-05-2024, 06:43 AM Last Post: Vojno |
BMW G8x Coolant Temp error | Airbus | 3 | 99 |
30-05-2024, 23:09 PM Last Post: krug |
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content