Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

HQ op-com 2014
11-07-2014, 07:25 AM,
Post: #21
KOpel  RE: HQ op-com 2014
(09-07-2014, 19:56 PM)obdstart Wrote:  
(09-07-2014, 11:40 AM)mpautoservis Wrote:  Friends.

Does anyone have the english version 31223c with firmear 1.59, that may have worked with Chinese older clone, with a regular chip.
It remains to be tested.

Regards

My advice: dont try because you f..k chinese interface, especially with a fake chip... so choice is yours..

I have OPCOM with microchip PIC18F458 V5
Quote this message in a reply
11-07-2014, 08:19 AM,
Post: #22
RE: HQ op-com 2014
(11-07-2014, 07:25 AM)mpautoservis Wrote:  
(09-07-2014, 19:56 PM)obdstart Wrote:  
(09-07-2014, 11:40 AM)mpautoservis Wrote:  Friends.

Does anyone have the english version 31223c with firmear 1.59, that may have worked with Chinese older clone, with a regular chip.
It remains to be tested.

Regards

My advice: dont try because you f..k chinese interface, especially with a fake chip... so choice is yours..

I have OPCOM with microchip PIC18F458 V5

.......How to check what chip in tool?

                                                               
Was I helpful? Please support my time and Hit [Image: tyl_add.png]  And [Image: postbit_reputation.gif] -button's.

NEW Trasdata 9 Master support Bosch SM(service mode) etc enjoy
Quote this message in a reply
11-07-2014, 08:33 AM,
Post: #23
RE: HQ op-com 2014
Remove 4 screws on the casing & open it !!
Fake will say OPCOM on the mcu + 2013 on the board
Quote this message in a reply
[+] 2 users say Thank You to McLuvin for this post
11-07-2014, 08:42 AM,
Post: #24
RE: HQ op-com 2014
(11-07-2014, 08:33 AM)McLuvin Wrote:  Remove 4 screws on the casing & open it !!
Fake will say OPCOM on the mcu + 2013 on the board

What chip is good one(clone)?

                                                               
Was I helpful? Please support my time and Hit [Image: tyl_add.png]  And [Image: postbit_reputation.gif] -button's.

NEW Trasdata 9 Master support Bosch SM(service mode) etc enjoy
Quote this message in a reply
11-07-2014, 08:45 AM,
Post: #25
RE: HQ op-com 2014
(11-07-2014, 08:42 AM)Bimmeristi Wrote:  
(11-07-2014, 08:33 AM)McLuvin Wrote:  Remove 4 screws on the casing & open it !!
Fake will say OPCOM on the mcu + 2013 on the board

What chip is good one(clone)?

CLICK ME POST #22
Quote this message in a reply
[+] 2 users say Thank You to McLuvin for this post
11-07-2014, 09:29 AM, (This post was last modified: 27-11-2018, 13:19 PM by mattydr67.)
Post: #26
RE: HQ op-com 2014
Pics with a opcom v5 hardare and real Microchip PiC18F458 you can see in the first post of this thread.
Good luck
Quote this message in a reply
11-07-2014, 09:40 AM, (This post was last modified: 11-07-2014, 10:00 AM by Bimmeristi.)
Post: #27
RE: HQ op-com 2014
I have OPCOM with microchip PIC18F458, so is it V5 or what...?

Is there another software where is activated done? I have tried few and only software (-2008 car support) has. No newer can use, it ask activation when try to do diagnostic.

                                                               
Was I helpful? Please support my time and Hit [Image: tyl_add.png]  And [Image: postbit_reputation.gif] -button's.

NEW Trasdata 9 Master support Bosch SM(service mode) etc enjoy
Quote this message in a reply
11-07-2014, 11:29 AM,
Post: #28
RE: HQ op-com 2014
There is china clone software uploaded 2010-08 already on this site try using that as other software needs Modded clone
Try doing a bit off reading before asking the same answered questions wink
Quote this message in a reply
11-07-2014, 11:49 AM,
Post: #29
RE: HQ op-com 2014
So, story short
China clone V5 the one with real PIC18F458 works with 08 2010 china.
This one , write ftdi with ept from vaux-com 2012 thread and upgrade flash with ocflash to 1.45 and it will work with VAUXCOM120309a
Also this one can be transformed in a "HQ" clone if you modd ftdi dump with some extra bits and then you will be able to run it with modified software for hq clone with fw: ro-1.47 ; op-com 131223cen 1.59 or vaux-com 131223d 1.60.
Also as i have seen on another forum this clone B/B+ can be modded to support CHSCAN and like this will be transfomed to C/C+

If you like my post and it helped you please press [Image: postbit_reputation.gif][Image: tyl_add.png]
Quote this message in a reply
[+] 6 users say Thank You to fantomel for this post
12-07-2014, 10:12 AM,
Post: #30
KOpel  RE: HQ op-com 2014
(11-07-2014, 11:49 AM)fantomel Wrote:  So, story short
China clone V5 the one with real PIC18F458 works with 08 2010 china.
This one , write ftdi with ept from vaux-com 2012 thread and upgrade flash with ocflash to 1.45 and it will work with VAUXCOM120309a
Also this one can be transformed in a "HQ" clone if you modd ftdi dump with some extra bits and then you will be able to run it with modified software for hq clone with fw: ro-1.47 ; op-com 131223cen 1.59 or vaux-com 131223d 1.60.
Also as i have seen on another forum this clone B/B+ can be modded to support CHSCAN and like this will be transfomed to C/C+
Very interesting story. smile
I am ready to sacrifice my OPCOM, but I need ftdi dump and modified software for hq clone.
Does anyone have it all? handshake
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
KOpel Opel EPC 4.25 (10.2014) jahacmm73 11 10,091 15-08-2022, 22:51 PM
Last Post: carradio2001
KOpel Corsa D steering column 2007-2014 issue sakroda 0 338 13-05-2022, 08:58 AM
Last Post: sakroda
KOpel [GAVE UP] GM EPC 2014 Install Help Ecutech 1 658 21-02-2019, 12:50 PM
Last Post: Ecutech
  2014 Insignia pbz151 2 1,075 15-12-2018, 21:39 PM
Last Post: Wibo
KOpel Opel/Vauxhall EPC 4.25 (10.2014) Multilanguage 23Andi23 18 15,403 15-10-2018, 20:30 PM
Last Post: KEATMAR
KOpel Tech2Win V2.264 2014-01-13 23Andi23 0 1,619 02-09-2014, 09:32 AM
Last Post: 23Andi23

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content