[laso]

I have a prolem with the EZS replacement in AUDI Q7.

There is immoff in the ECU and on the purchased EZS set, the car key starts immediately, and there are CP errors.
The car is from 2007 and the set is from 2011.
 SMOK was unable to login
I could not add it using SMOK or AUTEL.
At the stage of asking about Power class, Autel reports an error (ecu has immo off).
I bought a kit from the 2007 car, I copied the eeprom and flash and the car still does not start.
I will only add that when there was an ALL key lost procedure in this car (I do not know if it matters)

[rs@chip]

I have a prolem with the EZS replacement in AUDI Q7.

There is immoff in the ECU and on the purchased EZS set, the car key starts immediately, and there are CP errors.
The car is from 2007 and the set is from 2011.
 SMOK was unable to login
I could not add it using SMOK or AUTEL.
At the stage of asking about Power class, Autel reports an error (ecu has immo off).
I bought a kit from the 2007 car, I copied the eeprom and flash and the car still does not start.
I will only add that when there was an ALL key lost procedure in this car (I do not know if it matters)

thats normal if ecu is immo off and tool try to read pin from it there will be error.. try add pin manualy or yust clone the ezs and done

[laso]

I have a prolem with the EZS replacement in AUDI Q7.

There is immoff in the ECU and on the purchased EZS set, the car key starts immediately, and there are CP errors.
The car is from 2007 and the set is from 2011.
 SMOK was unable to login
I could not add it using SMOK or AUTEL.
At the stage of asking about Power class, Autel reports an error (ecu has immo off).
I bought a kit from the 2007 car, I copied the eeprom and flash and the car still does not start.
I will only add that when there was an ALL key lost procedure in this car (I do not know if it matters)

thats normal if ecu is immo off and tool try to read pin from it there will be error.. try add pin manualy or yust clone the ezs and done

As I wrote in the post, I also bought an EZS from 2007 and it cloned and the car still does not start. Both EZS had the same MASK. When adding Autel, I entered PIN and CS by hand.
Car has two keys and two keys are recognizable

[rs@chip]

I have a prolem with the EZS replacement in AUDI Q7.

There is immoff in the ECU and on the purchased EZS set, the car key starts immediately, and there are CP errors.
The car is from 2007 and the set is from 2011.
 SMOK was unable to login
I could not add it using SMOK or AUTEL.
At the stage of asking about Power class, Autel reports an error (ecu has immo off).
I bought a kit from the 2007 car, I copied the eeprom and flash and the car still does not start.
I will only add that when there was an ALL key lost procedure in this car (I do not know if it matters)

thats normal if ecu is immo off and tool try to read pin from it there will be error.. try add pin manualy or yust clone the ezs and done

As I wrote in the post, I also bought an EZS from 2007 and it cloned and the car still does not start.  Both EZS had the same MASK.  When adding Autel, I entered PIN and CS by hand.
Car has two keys and two keys are recognizable

than u have compatibility isue betwen the units.. there are 2 generations

[laso]

They have a total of 3 EZS.
One with the key, but I can not retrofit it with SMOK and AUTEL after OBD and this is EZS 2nd gen.
I copied to the same EZS as my original one, i.e. from Motorola 1L59W.

[maros4341]

if original FBS ( EZS ) exist - it is the better way to restore original

[Gabriel87]

Read old with vvdi prog eeprom and flash and write with new easy joob.

[laso]

I cloning with vvdi prog and car still not stars.

[Gabriel87]

I cloning with vvdi prog and car still not stars.

write eeprom and flash?

[laso]

Yes. Of course. I write both