Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
FRM Bench Test
08-10-2022, 11:16 AM,
Post: #1
|
|||
|
|||
FRM Bench Test
Hello
I want to make an test bench cable , so i can program and test frm directlyy on bench. I have aJBFE from E9x , obd socket , but i don't know , exactly the wires that need to connect the obd connector. I saw that from JBFE to FRM i need to connect the CAN wires , but from JBFE to OBD how do i connect them ? Someone have an schematic ? Thank you |
|||
08-10-2022, 11:36 AM,
Post: #2
|
|||
|
|||
RE: FRM Bench Test
Here you go for programming the FRM with VVDI PROG
xxxxxxxxxxxxxxxxxxxxxxxxxx |
|||
08-10-2022, 11:43 AM,
Post: #3
|
|||
|
|||
RE: FRM Bench Test
|
|||
08-10-2022, 11:59 AM,
Post: #4
|
|||
|
|||
RE: FRM Bench Test
(08-10-2022, 11:16 AM)DaBotta Wrote: Hello Is this OK? |
|||
08-10-2022, 12:18 PM,
Post: #5
|
|||
|
|||
RE: FRM Bench Test
(08-10-2022, 11:59 AM)Arthur_79 Wrote:(08-10-2022, 11:16 AM)DaBotta Wrote: Hello Hello , i saw the newtis diagram , but i think JBBFE don't have that K Can connector , only CAN Low and High , those one cannot connect directly to obd , right ? Need some different can transformer ? |
|||
08-10-2022, 12:59 PM,
Post: #6
|
|||
|
|||
RE: FRM Bench Test
(08-10-2022, 12:18 PM)DaBotta Wrote:(08-10-2022, 11:59 AM)Arthur_79 Wrote:(08-10-2022, 11:16 AM)DaBotta Wrote: Hello CAN Low and High connect directly to obd socket. No need CAN transformer. |
|||
Reputation: +1 - ROD-BENDERS [+1] | |||
10-10-2022, 07:26 AM,
Post: #7
|
|||
|
|||
RE: FRM Bench Test
The JBE (built into the JBBF) is the gateway.
The gateway has all(!) available connections, also to OBD connector with D-CAN (500kBit/sec) / K-Line, also to K-CAN (100kBit/sec). |
|||
14-10-2022, 20:03 PM,
Post: #8
|
|||
|
|||
RE: FRM Bench Test
Tried all the wiring , and
NO RESPONSE FROM CONTROL UNIT . What i am doing wrong .... FRM X14261 Pin 12 Wake Up -> 12V X14260 Pin 43 PT CAN_L -> JBE PIN 2 Blue Socket X14260 Pin 44 PT_CAN_H -> JBE PIN 1 Blue Socket X14260 Pin 45 K_CAN_l -> JBE PIN 10 Blue Socket X14260 Pin 46 K_can_H -> JBE PIN 46 Blue Socket All the powers and wake up for both modules OBD Tried even PIN 33 to PIN 7 OBD D_TXD1 and even PIN 33 D_CAN_L to PIN 14 OBD and PIN 17 D_CAN_H to PIN 6 OBD Same result. The JBE is from 2008 / 09 What i am doing wrong ? |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content