[ahmadarifai]

I have an F90 that have 2 bad ECUs i циLoскёd donors with same рдят number and then i wrote original files to donors and car started fine but i got the below permanent errors in photo, i tried flashing and coding without success. appreciate any ideas for direction 

021204    DME: Function enable, engine speed limitation, power stage 1: Malfunc

021304    DME 2: Function enabling 2, internal check: Marginal conditions not me

182904     DME: Function enable, speed limitation: Code invalid

182905      DME 2: Function enable, top speed limitation 2: Code invalid

1F2102       DME: Internal fault (increase of performance not enabled)

1F2112        DME 2. Function enable, power increase 2: not occurred

[ivanivanusic]

I have an F90 that have 2 bad ECUs i циLoскёd donors with same рдят number and then i wrote original files to donors and car started fine but i got the below permanent errors in photo, i tried flashing and coding without success. appreciate any ideas for direction 

021204    DME: Function enable, engine speed limitation, power stage 1: Malfunc

021304    DME 2: Function enabling 2, internal check: Marginal conditions not me

182904     DME: Function enable, speed limitation: Code invalid

182905      DME 2: Function enable, top speed limitation 2: Code invalid

1F2102       DME: Internal fault (increase of performance not enabled)

1F2112        DME 2. Function enable, power increase 2: not occurred

You need to inject f5сs to enable features.
I think it’ll solve almost all erorrs there.

[Rajco]

f5с didnt be cloned?

[ahmadarifai]

I did not clone f5с, someone messed around with the original ECUs they have the same faults as above in addition to other faults.

so this needs f5сs update?

[Mattyemme]

I did not clone f5с, someone messed around with the original ECUs they have the same faults as above in addition to other faults.

so this needs f5сs update?

check f5с and if there are REJECT...send VIN and we can help you to have all f5с

[ahmadarifai]

So i read the f5сs and there was 1 Rejected in each DME so i deастїvатёd the relevant f5с since i couldn't find it in the repair pack i thought maybe the car does not have it, the errors became 4 not 6, i think the way i cloned could be the problem, i циLoскёd donors and then wrote original flash + eeprom using the programmer, i attached certificates LOG in DMEs that i read.

the ones rejected where 0x95  in DME1 and 0x7B in DME2

[megalo84]

There are no f5с codes in the repair package,
The codes you found in the ECU were probably from the donor car. Here are the details:
AppID 149(0x95) Vmax Off DME1
AppID 123(0x7B) Vmax Off DME2

I think you need to do a WH reset as power monitoring is active

[ahmadarifai]

Yes Maybe Working Hours issue, but i have clean backup of the ECUs even before when someone messed them up, and as per other threads when you write original dumps working hours are copied to the donors. or maybe because of the original dumps are a bit old like 3 months ago?

i tried again and циLoскёd then wrote original files the errors were gone, but came back after flash + code. i will attach the dumps if some one could reset working hours.

[d.martynov]

Yes Maybe Working Hours issue, but i have clean backup of the ECUs even before when someone messed them up, and as per other threads when you write original dumps working hours are copied to the donors. or maybe because of the original dumps are a bit old like 3 months ago?

i tried again and циLoскёd then wrote original files the errors were gone, but came back after flash + code. i will attach the dumps if some one could reset working hours.

Try these files. I've also added them to the f5с archive if you still need them. These aren't the original f5сs, but they might work.

[user0086]

Maybe someone messed with the FA and now you programmer the incorrect software?