[pietje001]

You must change dash + cas.
digiprog can change dash (but you probably need to replace the 35080 chip).
you can buy R260 (it's better than R270) to change cas

[bara001]

You must change dash + cas.
digiprog can change dash (but you probably need to replace the 35080 chip).
you can buy R260 (it's better than R270) to change cas

Hi. Thanks for the reply.
I used fvdi to change CAS2.
Now I don't have a blank 35080 chip.
Is R270 reliable for changing km in dash 35080 chip?
I can buy R270 for use of 35080 in dash only. But is it reliable for this job ?

[funky1za]

W203 MB C230 V6 - done via obdii - no issues

[pietje001]

W203 MB C230 V6 - done via obdii - no issues

what year? thnx

[Macman07]

Hello,
I have tested to change the kilometers on the dash on VW golf IV tdi 2000 with my digiprog3 clone v4.94 by obd. But whitout any results.
He dont read me the kilometers, he give me an "?". Anyway, I write the new kilometeres, and he say me test 0, test 1 etc.., and "wegfahrspeere kodieren 0x00" (immo code).
Does someone know what I have to do here??

I pressed "X", and I have waited so much time, so i've cut the digiprog alimentation.
The kilometers on the dashboard displayed the old. But all is ok with the dashboard, everything works well .

Of course, in the process, the ingnition was on!

Thanks in advance!

Best regards

[volavka]

Digiprog3 v94 not work on mercedes w204 2011 ?
i change dash ,, but after 3 secound old km back
also i change from ezs uthig happend , after 3 secoud old km back
any help ?
thak you

[Dayo]

Do ezs. Itll make it to 1.6m and itll ask for new mileage. It breaks the sync so you can do the dash on its own from now on. It works fine for me

[pietje001]

You have to to :
-car-merc-w204-tacho, and:
-car-merc-w204-ezs

but i'm not sure what the correct order is.
if it jumps back after second option, I do the first option again. then i always works.
for example:
-car-merc-w204-tacho
-car-merc-w204-ezs
-car-merc-w204-tacho


but if you have the facelift model (2011-2014), then maybe it doesnt work because it might have more places where it storage mileage. I had this with a w212 model, changed the dash+ezs, but still old mileage came back. apparently it has 2 storage locations extra, for example it remembers the mileage before your last drive. (but then it jumps back to for example 30km earlier, not exactly the same mileage)
i think this could be changed anyway, but can't remember how..

[kizagt]

Hi members.
I am trying to do BMW (E90, E87, E62)
Must I only change mileage in CAS and it will automatically change in instrument cluster or I must change both ?
I have digiprog3 4.88 and fvdi.
Digiprog and fvdi cannot change mileage in instrument cluster.
Can I buy R270 for changing the mileage in clusters?
Thanks

yes you need to do dash also 35080v6 inside
i didn t have lucky with r270(my clone) i need to put new chip in dash (35080v6)
it is not problem to read and save, problem is to erase and write

---

Hello,
I have tested to change the kilometers on the dash on VW golf IV tdi 2000 with my digiprog3 clone v4.94 by obd. But whitout any results.
He dont read me the kilometers, he give me an "?". Anyway, I write the new kilometeres, and he say me test 0, test 1 etc.., and "wegfahrspeere kodieren 0x00" (immo code).
Does someone know what I have to do here??

I pressed "X", and I have waited so much time, so i've cut the digiprog alimentation.
The kilometers on the dashboard displayed the old. But all is ok with the dashboard, everything works well .

Of course, in the process, the ingnition was on!

Thanks in advance!

Best regards

This is normal for golf mk4.. Just press V or X and wait need 1/2 till 1 hour to finish. Left with ingition on and be patient

[Dayo]

Will digi do a 2010-2011 audi tt???