Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
DIGIPROG 3 user help thread !
11-07-2015, 22:26 PM,
Post: #171
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
You must change dash + cas.
digiprog can change dash (but you probably need to replace the 35080 chip). you can buy R260 (it's better than R270) to change cas |
|||
Reputation: +1 - Clusters [+1] | |||
11-07-2015, 22:41 PM,
Post: #172
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(11-07-2015, 22:26 PM)pietje001 Wrote: You must change dash + cas. Hi. Thanks for the reply. I used fvdi to change CAS2. Now I don't have a blank 35080 chip. Is R270 reliable for changing km in dash 35080 chip? I can buy R270 for use of 35080 in dash only. But is it reliable for this job ? |
|||
19-07-2015, 18:51 PM,
Post: #173
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
W203 MB C230 V6 - done via obdii - no issues
|
|||
19-07-2015, 21:44 PM,
Post: #174
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
|
|||
21-07-2015, 12:32 PM,
Post: #175
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Hello,
I have tested to change the kilometers on the dash on VW golf IV tdi 2000 with my digiprog3 clone v4.94 by obd. But whitout any results. He dont read me the kilometers, he give me an "?". Anyway, I write the new kilometeres, and he say me test 0, test 1 etc.., and "wegfahrspeere kodieren 0x00" (immo code). Does someone know what I have to do here?? I pressed "X", and I have waited so much time, so i've cut the digiprog alimentation. The kilometers on the dashboard displayed the old. But all is ok with the dashboard, everything works well . Of course, in the process, the ingnition was on! Thanks in advance! Best regards |
|||
04-08-2015, 23:25 PM,
Post: #176
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Digiprog3 v94 not work on mercedes w204 2011 ?
i change dash ,, but after 3 secound old km back also i change from ezs uthig happend , after 3 secoud old km back any help ? thak you BEST CHIPTUNING SERVICE BY Zenter Performance
Contact Skype: zenter-88 Facebook: https://www.facebook.com/ZenterPerformance -------------------------------------------------------------------------------------------------------------- highest Quality ChiPTuninG Files BY PTF Team https://performance-tuningfiles.com/ POWER BY TECHNOLOGY -------------------------------------------------------------------------------------------------------------- BEST CHIPTUNING SERVICE BY Jurebv Contact Skype: live:jure.coric_1 https://files.tuning-makarska.com/ -------------------------------------------------------------------------------------------------------------- - IMMO/ECU , ODO , AIRBAG , CARRADIO , TESTED SOLUTIONS UNDER MY SOFTWARE In progress TUNING STAGE1/DPF/SCR/EGR/TVA/FLAP/ START STOP OFF Software WHAT'S NEWS ! -Steering Angle Sensor Restore For LEXUS,TOYOTA,SUBARU,MITSUBISHI,VAG -Citroen DS5 Steering lock Renew/Write Code by dumps -Passat CCM Repair corrupted dump succes -VAG ECU SIMOS PCR 2.1 KM WITH CRC CORRECTED ! -IMMO OFF For NISSAN/INIFINITI with HITACHI ECU | CPU SH705X -Dacia Dashboard with Fujitsu MB96F6A6 Change km/Block Synchro Dash-ABS -=[Full WinOLS/ECM Titanium User] =- Remember! dirty hands are a sign of clean money шшш.αήkαbôôτ.Ćô.цk |
|||
05-08-2015, 00:12 AM,
Post: #177
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Do ezs. Itll make it to 1.6m and itll ask for new mileage. It breaks the sync so you can do the dash on its own from now on. It works fine for me
Stop getting worried about what could go wrong, and start getting excited about would could go right!
hmmmmmmm........eeprom!!! Digi v4.94, Xtool, R260, R270, Smok, VagProg DataSmart 3+ Smelecom, Autel Maxisys ms908 |
|||
06-08-2015, 10:42 AM,
Post: #178
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
You have to to :
-car-merc-w204-tacho, and: -car-merc-w204-ezs but i'm not sure what the correct order is. if it jumps back after second option, I do the first option again. then i always works. for example: -car-merc-w204-tacho -car-merc-w204-ezs -car-merc-w204-tacho but if you have the facelift model (2011-2014), then maybe it doesnt work because it might have more places where it storage mileage. I had this with a w212 model, changed the dash+ezs, but still old mileage came back. apparently it has 2 storage locations extra, for example it remembers the mileage before your last drive. (but then it jumps back to for example 30km earlier, not exactly the same mileage) i think this could be changed anyway, but can't remember how.. |
|||
06-08-2015, 15:04 PM,
(This post was last modified: 06-08-2015, 15:15 PM by kizagt.)
Post: #179
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(11-07-2015, 21:36 PM)bara001 Wrote: Hi members. yes you need to do dash also 35080v6 inside i didn t have lucky with r270(my clone) i need to put new chip in dash (35080v6) it is not problem to read and save, problem is to erase and write (21-07-2015, 12:32 PM)Macman07 Wrote: Hello,This is normal for golf mk4.. Just press V or X and wait need 1/2 till 1 hour to finish. Left with ingition on and be patient |
|||
08-08-2015, 09:06 AM,
Post: #180
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Will digi do a 2010-2011 audi tt???
Stop getting worried about what could go wrong, and start getting excited about would could go right!
hmmmmmmm........eeprom!!! Digi v4.94, Xtool, R260, R270, Smok, VagProg DataSmart 3+ Smelecom, Autel Maxisys ms908 |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content