Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

(SOLVED) E60 SZL, DSC error after attempted VO coding
31-03-2018, 20:45 PM, (This post was last modified: 12-04-2018, 11:55 AM by willisodhiambo.)
Post: #1
(SOLVED) E60 SZL, DSC error after attempted VO coding
I was trying to code VO in E60 to change from Japan to ECE using abrites. Cant recall but I think i coded VO to DSC and SZL and AFS.

Now I have a DSC error on cluster and SZL error "not initialized" in ISTA, Attempts to initialize fail as the program seems to hang at the beginning when it requires lock to lock steering manipulation for active steering initialization.

It is as if SZL is not being seen or has stopped transmitting or there is a mismatch between coding if related DSC partner ECUs. I have programed it with WINKFP successfully, then default coded it with NCSExpert. No luck.

I am at a loss, the unit must be recoverable or there is a minor step am missing. Any leads? I would be grateful for suggestions.
Quote this message in a reply
01-04-2018, 10:29 AM,
Post: #2
RE: E60 SZL, DSC error after attempted VO coding
On which step intilization fails?
Quote this message in a reply
03-04-2018, 07:52 AM,
Post: #3
RE: E60 SZL, DSC error after attempted VO coding
(01-04-2018, 10:29 AM)Silva1337 Wrote:  On which step intilization fails?

It was failing at the very beginning is the active steering alignment ABL when the steering should be turned left and right. Did it 20 times, nothing, like it hanged. It is as if it is not reading steering angle from SZL.
Quote this message in a reply
03-04-2018, 11:14 AM,
Post: #4
RE: E60 SZL, DSC error after attempted VO coding
vin is written in szl?
Quote this message in a reply
03-04-2018, 12:02 PM, (This post was last modified: 03-04-2018, 12:03 PM by Silva1337.)
Post: #5
RE: E60 SZL, DSC error after attempted VO coding
(03-04-2018, 07:52 AM)willisodhiambo Wrote:  
(01-04-2018, 10:29 AM)Silva1337 Wrote:  On which step intilization fails?

It was failing at the very beginning is the active steering alignment ABL when the steering should be turned left and right. Did it 20 times, nothing, like it hanged. It is as if it is not reading steering angle from SZL.

Do you know that you need move steering wheel only few milimeters to left and right when performing calibration?
You say angle not seen how about when you turn of engine?
if you have inpa check uif of szl afs , and if vin not correct , correct it by flashing it , then code on empty man , then try perform calibration again.
Quote this message in a reply
12-04-2018, 11:56 AM, (This post was last modified: 12-04-2018, 11:58 AM by willisodhiambo.)
Post: #6
RE: (SOLVED) E60 SZL, DSC error after attempted VO coding
Well the SZL was working before all this. The initial initialization instruction is to turn full lock both sides. Nothing was happening.

So someone with autoboss connected and performed the alignment straight up as they tell me.

No idea why ISTA had a problem. Very funny.
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  FDL coding BMW Apps Mugga 3 122 4 hours ago
Last Post: Mugga
XZBMW Coding a F80 M3 race car PeterY 10 476 Yesterday, 23:32 PM
Last Post: Furgus
XZBMW Esys error message only on EPS. ''Failed to get CAFs for SWE'' arthur101 2 99 Yesterday, 22:48 PM
Last Post: arthur101
  BMW E83 A1 error - MRS: No message from DSC ... ivanp 26 1,271 Yesterday, 13:20 PM
Last Post: ivanp
  NBT Evo CAFD missing after coding error Mugga 13 602 24-04-2024, 22:47 PM
Last Post: Mugga
XZBMW 6wb cluster swap and coding xMoses 4 232 22-04-2024, 19:07 PM
Last Post: NikolaIMRS
XZBMW M performance brake DSC2 SBRE coding Ckh091020 3 217 22-04-2024, 12:58 PM
Last Post: Ckh091020
  pulling both paddles put transmission into neutral coding tintoverano 1 118 22-04-2024, 12:42 PM
Last Post: raresh.tazz
  BMW F20 ACSM4B internal error Pedrom92 4 144 21-04-2024, 21:54 PM
Last Post: Pedrom92
XZBMW F20 LCI2 black panel cluster coding sqorpius 9 2,010 21-04-2024, 12:38 PM
Last Post: Adekborys69

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content