[ccfj1]

Hi All,

I have a working bench setup for the e9x and have a CAS, elv, key, Kombi and JBR.



All are connected together and i can see the aif in inpa and see the modules.



I can use NSC expert to code both the CAS and the JBR, and i could code the kombi, but when i try and code the kombi up now i get a "coding is faulty" and an error code or 2063. the man file is 9k and the trc file goes to 236k (after a code fail)????.

even a read file from the kombi loaded straight back on to the kombi does not work and it has no changes!!! i cant even default the kombi...



I'm running a K D-can lead (the clear one) and a datum set of v57 (i have 60 and 62 as well), i also have winkftp loaded and have imported the daten files, I can even update the firmware on the kombi, but not code it???

I can't code the CAS as i get a coms error when i remove the key (but still have the power on).



I want to change the vin on the CAS and the kombi and when i use tool32 i get the okay when i "code" the aif_shreiben, but the vin stays the same in both the CAS and the kombi.

I've been trying for two days solid to try and change the vin and have read loads of web pages on the web, but i can not find a workable tool32 guide.

Its driving me mad! lol

Can anyone offer an ideas as to why i cant change the vin in the cas and the kombi

and

why i can now no longer code the kombi via NSCexpert.

Cheers

[inotherwords]

AIF contains information about the software. The VIN number in it is just for info, it's not used anyhow by KOMBI/CAS.

[larshutten]

You can’t code kombi because vin numbers doesn’t match. And you can’t just simple change the vin number in cas and kombi with ncs/tool32/winkfp. You need other tools for that. R270 or VVDI for example.

[ccfj1]

You can’t code kombi because vin numbers doesn’t match. And you can’t just simple change the vin number in cas and kombi with ncs/tool32/winkfp. You need other tools for that. R270 or VVDI for example.

Ah ok, I have read it is possible, but i think you are correct, i can not do it with the tools i have....

Cheers.

Any ideas as to why i cant code the kombi now??

[dazuc]

You can’t code kombi because vin numbers doesn’t match. And you can’t just simple change the vin number in cas and kombi with ncs/tool32/winkfp. You need other tools for that. R270 or VVDI for example.

Ah ok, I have read it is possible, but i think you are correct, i can not do it with the tools i have....

Cheers.

Any ideas as to why i cant code the kombi now??

Because vin is being read from CAS, then attempting to code with that vin.

If you change vin in NCS when reading FA, then you can code it.

[ccfj1]

Any ideas as to why i cant code the kombi now??

Because vin is being read from CAS, then attempting to code with that vin.

If you change vin in NCS when reading FA, then you can code it.

Hmmm, ok, what would be the steps to do that?

---

Hold on I think I have done it....

[ccfj1]

OK, all coded up.

However, as a quick test, i have now go this when I attepmt to update the firmware o the kombi.



The updates gets 2 2% and then fails with the code above.

Any ideas? anyoine

---

Never mind, all done, managed to get the firmware to run.

[teerak2uk]

How does r270 change the vin???

[ccfj1]

From what i can gather, it dumps the contents of the vin chip, you then hex edit it and then dump it back, overwriting the config with blank data, its then available to code it tool32 or winkftp or even ncs

[matigdy]

For the future... if you have different VIN in CAS and KOMBI you have to use SG_CODIEREN_OHNE_VIN instead SG_CODIEREN then kombi will code with cas/frm vo (depends which one you have chosen) and .MAN coding work too