[shlema]

Hi, Smart ppl.
I am pulling my last hair out , can’t get KOMBI get back on line.
I have 2016 X1 F48 prod date 15/09, sw ship 1507504.
I retrofited rear PDC and backup camera, camera new retrofit and PDC module used.
Installed and fitted 4 rear sensors, PDC module and ICAM.
Now, because PDC was used and came from Europe, I need to flash it and coded to my car.
PDC prerequisites was BDC_GW. Flashed PDC with BDC_GW and coded as well as HU and BDC. I have all options come up on CID and pdc start working the ways it’s supposed, but options on CID like change dynamic lines, brightness etc are all greyed out, but that is not a huge problem, I can deal with that later. Also, tried to flash ICAM ( it was new ), but got error about ftp and tftp, left it alone for now.
 
The real problem I am getting with TPM malfunction, service engine light on and no Date/Time on instrument cluster and CID.
I didn’t touch KOMBI, but some reason now it is not showing up on the list while reading ECUs. After I do SVT calculation it’s there and with yellow folder while all others are blue/red.
ICAM is yellow as well (could be why options are greed out in PDC options). When tried to reflash KOMBI got an error ‘P2 timeout on Service RDBI_SVK has error in reslult: [Severity=2051]’ resource not available P2 timeout occurred. 
 
Guys, I need your help if that could be fixable and I can get my KOMBI back to answer.
Thank you.

[SweetBMW]

Did you Flash with enet? Or with icom? Enet directly connected to laptop is not recommended to flash Ethernet control
Units.

[jeroenbmw]

Hi, Smart ppl.
I am pulling my last hair out , can’t get KOMBI get back on line.
I have 2016 X1 F48 prod date 15/09, sw ship 1507504.
I retrofited rear PDC and backup camera, camera new retrofit and PDC module used.
Installed and fitted 4 rear sensors, PDC module and ICAM.
Now, because PDC was used and came from Europe, I need to flash it and coded to my car.
PDC prerequisites was BDC_GW. Flashed PDC with BDC_GW and coded as well as HU and BDC. I have all options come up on CID and pdc start working the ways it’s supposed, but options on CID like change dynamic lines, brightness etc are all greyed out, but that is not a huge problem, I can deal with that later. Also, tried to flash ICAM ( it was new ), but got error about ftp and tftp, left it alone for now.
 
The real problem I am getting with TPM malfunction, service engine light on and no Date/Time on instrument cluster and CID.
I didn’t touch KOMBI, but some reason now it is not showing up on the list while reading ECUs. After I do SVT calculation it’s there and with yellow folder while all others are blue/red.
ICAM is yellow as well (could be why options are greed out in PDC options). When tried to reflash KOMBI got an error ‘P2 timeout on Service RDBI_SVK has error in reslult: [Severity=2051]’ resource not available P2 timeout occurred. 
 
Guys, I need your help if that could be fixable and I can get my KOMBI back to answer.
Thank you.

KOMBI is responding by MOST if ptcan is connected and MOST is not good than kombi is not show up , programming and all is running by internal MOST channel.

Run with ISTA+ most configuration, this will bring back the kombi in most of the cases.

[shlema]

Thanks for all your replies,
I was able to get my KOMBI back, by reverting to original FA without 3AG and 507, recalculated SVT and TAL, then reflashed and voila .. it appeared on the list. Now ... i am missing time and date on cluster and CID. I've had set it 'Auto' in Settings, tried manual, but time just disappears, auto doesn't work at all.

any idea why ?

BTW, i don't have ICOM, but friend of mine can loan me one later next week.
Should i wait for ICOM to do any flashing/coding with ISTA+ just to be on safe side?

How do i run ISTA+ in most configuration ? i don't see any options for it.

Again, thanks for all your help.

[danyro]

Since 2 years, i flashed my f25 in 99% of cases with enet cable connected to gateway and not directly or to vin.
I used icom and dhcp server only when zgw2 needed and update.