Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Kess BMW E90 Wrong Protocol? Kline?
19-11-2018, 11:50 AM,
Post: #1
|
|||
|
|||
Kess BMW E90 Wrong Protocol? Kline?
Hi Fellas,
Again a problem while reading out a BMW E90 320d / 2005 / 110kW-150pk M47 engine Had also a 318D to do at the same time, succeed without ny problems(2007 EDC17) So when I looked at KSuite 2.47, I didn't find the model in the list, only the 163ps also M47 / EDC16C35 / prot 164 So I checked on Ksuite 2.23 and there I found it. But as EDC16C31 and protocol 159 I tried to read the ID, get a fault saying, "Wrong protocol, use protocol 164" So I tried tried the other one @163ps, read the ID and the same message appears "Wrong protocol, use protocol 164" while I choosed 164. Then I tried it with Ksuite 2.47, choosed the 320d 163ps prot 164 And again "Wrong protocol, use protocol 164" wile I used the 164 I have a backup tool, Chinese green PCB, did also the same on both softwares, checked different cables and stuff, no changes. What also was "weird", the 318d e90 that I did at the same time. Kess RED PCB EU version couldn't perform any read of the ecu or ID, then I toke the Green PCB one and job cleared reading and witing in 10 minutes... :s Im most considering about the fault "Wrong protocol, use protocol 164" I also reinstalled the both softwares and tried several times again, no changes every time "Wrong protocol, use protocol 164" Is it something knowed allready by you fellas...? Thanks in advance |
|||
19-11-2018, 12:03 PM,
Post: #2
|
|||
|
|||
RE: Kess BMW E90 Wrong Protocol? Kline?
(19-11-2018, 11:50 AM)TilQ34 Wrote: Hi Fellas, on 2005 there will be EDC16 if k-line told you wrong protocol chose can-bus |
|||
19-11-2018, 12:11 PM,
Post: #3
|
|||
|
|||
RE: Kess BMW E90 Wrong Protocol? Kline?
(19-11-2018, 12:03 PM)rs@chip Wrote:(19-11-2018, 11:50 AM)TilQ34 Wrote: Hi Fellas, Well that's what I did, I tried to read it out by Can.. Not by Kline Now e few minutes ago I found this while I was searching some info: https://www.amazon.co.uk/Diagnostic-Adap...B00O8079DY It says for "Diagnostics use till 2007" on BMW... Maybe I was wrong from the beginning by not using this adapter and read Kline instead like I did by Can cable :s |
|||
19-11-2018, 12:53 PM,
(This post was last modified: 19-11-2018, 13:22 PM by 23Andi23.)
Post: #4
|
|||
|
|||
RE: Kess BMW E90 Wrong Protocol? Kline?
(19-11-2018, 12:11 PM)TilQ34 Wrote: Well that's what I did, I tried to read it out by Can.. Not by Kline this adapter is only for simple kline interface with bridge from pin 7 to 8 to have kline on both pins you tried to change pullup in settings?? |
|||
19-11-2018, 14:40 PM,
Post: #5
|
|||
|
|||
RE: Kess BMW E90 Wrong Protocol? Kline?
This ECU Need via Kline and in Setup pull up resistor 225ohm
|
|||
Reputation: +1 - 23Andi23 [+1] | |||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content