Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
ZBE3 is not working anymore after I-Step Update with E-Sys
18-02-2019, 17:23 PM,
Post: #1
|
|||
|
|||
ZBE3 is not working anymore after I-Step Update with E-Sys
Hello,
i have retrofited the HU_NBT2 the Touchbox and the Touchcontroller in my F20 BJ:2012. Now i have tryed to update my I-Steps to 18-07-531. I updated with modifyed FA the HU_NBT2 and with the orginal FA: FEM_GW, FEM_Body, ACSM, DME, REM, Kombi and EPS. Now my Problem is that after i updated the orginal SGs the Retrofited ZBE3 is not working anymore. In E-Sys (load ECU) its not listed and Rheingold says "SG not found". I don´t have flashed the ZBE3. I don´t know why its not working anymore. Can you help me? Thanks |
|||
18-02-2019, 18:55 PM,
Post: #2
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
Before update everything worked?
ZGW module should be updated before other modules. You can check PreRequisite in E-Sys TAL editor |
|||
18-02-2019, 19:48 PM,
Post: #3
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
Yes, before the update the Controller works fine.
At the moment all SG aro on F20-18-07-531 exept the Touch Controller, i didn´t flash it. With my old CIC Controller (ZBE2) installed i can controll with the iDrive System. |
|||
18-02-2019, 21:04 PM,
Post: #4
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
Have you proper coding for it? What Zeitkriterium you use?
On SVT list is there ZBE2 still? |
|||
18-02-2019, 21:30 PM,
(This post was last modified: 18-02-2019, 21:31 PM by reclaim.)
Post: #5
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
I have tried it with ZK 0717 and 0718.
When the ZBE3 is connected E-Sys doesen´t show any ZBE device in SVT (when i klick Load ECU) Is the ZBE2 connected E-Sys show it as ZBE2. |
|||
19-02-2019, 04:00 AM,
Post: #6
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
My guess is probably your svt is not updated with zbe3. it still has the zbe2 in it.
thats why its not showing up. when you read svt it shows zbe2? when you read ecu it shows zbe2? would be worth a try to delete zbe2 from svt and update vcm then read ecu again see if zbe3 shows up and then write the new config in vcm. happens also when retrofitting from bkombi to dkombi because of same diag address it uses. of course first save your original svt before you try to make any changes.. |
|||
19-02-2019, 06:20 AM,
Post: #7
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
Can you perhaps write a Little How to Update VCM and delete ZBM2?
|
|||
19-02-2019, 07:28 AM,
Post: #8
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
Go to esys options
Mark update vsm update msm Read fa Activate fa Code any ecu in tree Read ecu and see zbe now BMW tuning & retrofitting, https://www.instagram.com/cebepspb/
* lifetime EVO, ROUTE codes, Carplay, ECU Remap and other crap |
|||
19-02-2019, 08:31 AM,
Post: #9
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
Thank you i will try this later
|
|||
19-02-2019, 18:10 PM,
Post: #10
|
|||
|
|||
RE: ZBE3 is not working anymore after I-Step Update with E-Sys
After updating the VCM i can see ZBE3 again and after VO Coding its working.
Again Thank you. |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content