Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
How to work out which zb to flash for used ecu without orginal ecu
20-03-2019, 14:33 PM,
(This post was last modified: 20-03-2019, 14:45 PM by Bavrian.)
Post: #1
|
|||
|
|||
How to work out which zb to flash for used ecu without orginal ecu
I have a car which came without any engine ecu or cas as these were missing
I have brought a replacement used ecu set with cas, key and engine ecu I need to know which zb I need to flash this engine ecu with for this car the engine ecu hardware number is the right one for the car how can one find out which engine ecu software to load to the used engine ecu with as there are many variants I have winkfp & ista p but winkfp gives 23 different versions the car in question is a E60 Jan 2007 pre lci 530d m57/t2 170kw/231bhp type code NR72 |
|||
20-03-2019, 14:50 PM,
Post: #2
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
ISTA-P , but first you need to change vin of CAS and DME with tool32 , otherwise ISTA-P will ask to replace those 2 ECU's
|
|||
20-03-2019, 15:07 PM,
(This post was last modified: 20-03-2019, 15:11 PM by Bavrian.)
Post: #3
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
cant seem to find command to write vin in tool32 its dde626 any other way around with tool32 |
|||
20-03-2019, 15:26 PM,
Post: #4
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
(20-03-2019, 15:07 PM)Bavrian Wrote: you can flash it with winkfp , choose any ZB for DDE626 but important is the correct VIN ( 17 digits ) . also make sure you write FA to CAS too before running ISTA-P . or , if CAS and DDE from same donor car , simply read FA with NCS from LMA and write to CAS then run ISTA-P .... ISTA-P will complaint about all other ECU's because of a VIN mismatch but will also show the correct ZB for CAS and DDE . copy those numbers and use WINKFP to flashing and VIN writing both CAS and DDE . |
|||
20-03-2019, 15:33 PM,
Post: #5
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
I tried aif schrieben to write vin the uif but it doesn't let me write there vin there
cant seem to find any other command, I understand for the above method to work on ista p it needs to see the correct car vin number to detect the correct firmware for the car vin and ecu is there any other solution |
|||
20-03-2019, 15:42 PM,
Post: #6
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
(20-03-2019, 15:33 PM)Bavrian Wrote: I tried aif schrieben to write vin the uif but it doesn't let me write there vin there ISTA-P doesn't decode the car specs from the VIN but from the FA stored in CAS and LMA , why are you using AIF Schreiben , that's not the correct command to use for VIN writing. |
|||
20-03-2019, 15:50 PM,
Post: #7
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
(20-03-2019, 15:42 PM)emhtuning Wrote:(20-03-2019, 15:33 PM)Bavrian Wrote: I tried aif schrieben to write vin the uif but it doesn't let me write there vin there that was the only command that allowed the uif to be changed nothing in there for the vin when I copy the fa from lm to cas and when I try to recode the cas it gives a vin error when I do fa write from lm to cas it goes ahead but after reconnecting with ncs it still picks up other car vin and fa which is strange so when I do connect with ista p its picking up other car vin and fa |
|||
20-03-2019, 16:43 PM,
Post: #8
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
you are not getting the idea here ,, copying FA from LM to CAS not for VIN change , its for ISTA-P to know the right ZB for CAS and DME ,,
sorry but looks like I am speaking an UNKNOWN language to you .. I am out |
|||
20-03-2019, 22:09 PM,
(This post was last modified: 20-03-2019, 22:10 PM by Bavrian.)
Post: #9
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
(20-03-2019, 16:43 PM)emhtuning Wrote: you are not getting the idea here ,, copying FA from LM to CAS not for VIN change , its for ISTA-P to know the right ZB for CAS and DME ,, i don't think you understood my reply from earlier when i copied the fa from lm to cas with fa write on cas when connecting to ista p it was still picking up other car vin so wasn't good idea to carry on but its sorted now with autohex new vin was written in cas and only after this it allowed ista p to pick up new vin i know fa write wouldn't change the cas vin thanks for your help & replies above |
|||
21-03-2019, 21:56 PM,
(This post was last modified: 21-03-2019, 23:02 PM by ____ANGEL___.)
Post: #10
|
|||
|
|||
RE: How to work out which zb to flash for used ecu without orginal ecu
(20-03-2019, 14:33 PM)Bavrian Wrote: I have a car which came without any engine ecu or cas as these were missing you have to work like this https://cartechnology.co.uk/showthread.p...619&page=3 very very very simple, searching in etk pre lci e60 530d m57n2: 7808222 is the only dde present, so dde626! So this will be your program file 7808222 and for data file that's: (according to reference number in 7808222.0da and last zb dde626.his) 7811730 manual---------------zb 7811719 7811733 eu3 manual-----------zb 7811722 7811734 auto-----------------zb 7811723 7811737 eu3 auto-------------zb 7811726 7811739 xdrive manual---------zb 7811728 7811740 xdrive auto-----------zb 7811729 cas zb 9147215 (part no. in etk is 6965050 and last zb for 6965050 is 9147215 according to cas260.his) you can't use software not matching your hardware, so hope that you buyed correct numbers cas and dde... why guys make you complicated things that are simple? |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content