[da14u]

Today I again installed the V139 of cedrsan without problems.
When connected to car and PC two leds are green and two - red.

But windows 7 did not ask for 4 old drivers. It has installed only one driver with name:
" 1B-Alliance Vehicule Communication Interface " with version 3.2.2.0 (26.07.2013)
this driver is of Bosch Automative Service Solutions SARL.

do I need install 4 drivers (if yes, how?) or that driver is enough?

Check this post, same link I gave you earlier and he also has just one driver installed with all leds lighting up fine, so my guess is it should be OK. I think the old device had four and the newer has one driver but I could be wrong as I myself don't have the newer clip to check. Have you tried diagnosing the car? What errors do you get? Post some screenshots of the errors.

http://garage-automotive.com/showthread....9#pid37729

[TizWoz]

I have installed version of Cedrsan without errors (first removed previous one). Thank you!

how I can know if hardware is correctly working? Is there Instructions available?

Some only need one driver. Best just to test it.

How better to test it?

PLUG IN CAR AND SEE

It looks to me like it was software problem.

[Gigan]

Some only need one driver. Best just to test it.

How better to test it?

PLUG IN CAR AND SEE

It looks to me like it was software problem.

Hi,
OKe, I will try today.
When fill VIN in the start form, what I need to fill in the "RO" position ?
What means RO?

[eudin77]

RO - Reparation Order.Fill with what you want.For example just one " 0 " is enough

[da14u]

I've updated POST#19 for the bluetooth instructions by cedrsan. Check it out how to pair the bluetooth.

http://garage-automotive.com/showthread....9#pid46289

[Gigan]

I've updated POST#19 for the bluetooth instructions by cedrsan. Check it out how to pair the bluetooth.

http://garage-automotive.com/showthread....9#pid46289

Can I first check the wired connection?, or first must be bluetooth pairing?

[TizWoz]

I've updated POST#19 for the bluetooth instructions by cedrsan. Check it out how to pair the bluetooth.

http://garage-automotive.com/showthread....9#pid46289

Can I first check the wired connection?, or first must be bluetooth pairing?

just use the USB , Worry about other later, I think you need working thing first.

[Gigan]

Now I can post some results:
the software is in Russian, but i will try to explain...
First of all it was able to determine automatically the correct VIN,
does it mean that clip works some how?
However few times it gave the initialization errors during computer test.
Finally after rebuting of PC, it gave some information.
I will post pics.

[da14u]

Now I can post some results:
the software is in Russian, but i will try to explain...
First of all it was able to determine automatically the correct VIN,
does it mean that clip works some how?
However few times it gave the initialization errors during computer test.
Finally after rebuting of PC, it gave some information.
I will post pics.

So indeed it was your software which is causing problems. If you can pull the VIN automatically then the canclip interface is OK. You just need to figure out your software, if you get random errors then definitely something wrong with your installation. If nothing helps i.e uninstalling canclp, drivers, registry setting etc..then the last hope is formatting. Format and start from fresh or try it on a PC where no canclip was installed before.

[Gigan]

        I dont know which results can be useful. Here are couple of pics. Please look.

1.) Clip takes too much power: after 15-17min the car battery (71A/H) goes dramatically down. It informs that cannot perform test because of low battery! I should charge it couple of times. Is it normal?
2. It works somehow with 1 driver, but I worry that better to have 4 traditional drivers with it, to be sure. I will think on reinstalling or using in other PC.

I wanted to reinstall wheel sensors in the Laguna 2. They are wrongly asigned.
By solving this task I could check Can clip.
How it is possble to do? Please advise.