ATTENTION !! Users which have not any posts were deleted !
  1. New Emulator

  2. Immo Bypass

  3. Julie Emulator

  4. AUTO CHIPS



Orange5 Clone [Support/Feedback/Rework/Calculators]
04-07-2017, 19:13 PM, (This post was last modified: 16-05-2019, 01:44 AM by volavka.)
Post: #1
0Dash  Orange5 Clone [Support/Feedback/Rework/Calculators]
I have just bought orange 5 programmer and all seems to work well happy

I got fed up with my genuine upa usb s programmer which didnt seem to want to read anything, it went through the motions and said success reading a load of zeros gavel

Straight out of the box this Orange 5 clone read and write eproms 95640 and 95P08C3 in circuit no problem with no errors, but I had to make sure that my connections to the chip via test clip were all good and then tool work like charm nerd

I think I like it so far smile

has anyone else any experience good or bad with this programmer ?

very simple to use.


Attached Files
1.jpg
File Type: .jpg
Downloaded: 636 times
Size: 2.49 MB

3.jpg
File Type: .jpg
Downloaded: 369 times
Size: 6.41 MB

2.jpg
File Type: .jpg
Downloaded: 293 times
Size: 6.26 MB


Tight lines and bending rods are what makes my day biggrin Zenter Performance tuning yes bowADBLUE-DTC-FAP-FLAP-EGR-LAMBDA-TQM-TPROT-VMAX-SPECIAL- LAUNCH CONTROL-POPCORN HARDCUT-MANUAL MEDCx17 IMMO OFF 100% - VAG IMMO OFF 2011+ 100% SEAT EDC17C74 2017 IMMO OFF here: bowtime skype:  PM
Reputation: +4 - Rhogan [+1] , raffy haddad [+1] , CHIKODIAG [+1] , Remap [+1]
Quote this message in a reply
[-] The following 15 users say Thank You to ROD-BENDERS for this post:
  • antonypaul, bekiyu, champagnecharly, CHIKODIAG, dara, dil6222, Dinho, gabivw, JarsaR, mikroel, RAFAA, raffy haddad, Rhogan, smtuning, strikeforce
06-07-2017, 10:51 AM,
Post: #2
RE: Orange 5 clone feedback
I was thinking to buy one but didn't find much report about
So i bought the mprog and waiting to received it
And maybe later i buy o5 when members here post theyre report
Regards
Quote this message in a reply
[-] The following 1 user says Thank You to raffy haddad for this post:
  • dara
06-07-2017, 14:57 PM, (This post was last modified: 06-07-2017, 15:00 PM by mikroel.)
Post: #3
Orange 5 clone feedback
I have it for a long time and for now everything is working properly.
One of the few clones that works well and works as an original.

Some adapters are not supplied and must be purchased separately

Sent from my iPhone using Tapatalk
Reputation: +1 - ROD-BENDERS [+1]
Quote this message in a reply
[-] The following 3 users say Thank You to mikroel for this post:
  • dara, JarsaR, ROD-BENDERS
06-07-2017, 16:51 PM, (This post was last modified: 06-02-2018, 22:58 PM by volavka.)
Post: #4
RE: Orange 5 clone feedback
Sadly i don't have clone one to leave feedback
did you try with hc908 secured ?

hmmm adapters look craps, soldering by hand

Mouad Amenchar Aka Volavka  yes
City: Tetouan - Country: Morocco

Email: volavka@hotmail.co.uk
skype: v0lavka
Facebook: VolavkaOfficialPage

WWW.CarTechnoloGY.co.uk
Reputation: +2 - ROD-BENDERS [+1] , Diagnostix [+1]
Visit this user's website
Quote this message in a reply
[-] The following 3 users say Thank You to volavka for this post:
  • dara, Diagnostix, ROD-BENDERS
06-07-2017, 18:47 PM, (This post was last modified: 06-07-2017, 18:47 PM by mikroel.)
Post: #5
RE: Orange 5 clone feedback
Adapters should be resolder for sure but it isn't so bad ,at all
The main point orange 5 clone isn't so bad as clones can be.
Good investment for sure . smile
Reputation: +1 - ROD-BENDERS [+1]
Quote this message in a reply
[-] The following 3 users say Thank You to mikroel for this post:
  • dara, JarsaR, ROD-BENDERS
06-07-2017, 19:20 PM,
Post: #6
RE: Orange 5 clone feedback
(06-07-2017, 18:47 PM)mikroel Wrote:  Adapters should be resolder for sure but it isn't so bad ,at all
The main point orange 5 clone isn't so bad as clones can be.
Good investment for sure . smile

So far its reading and writing (with verify) all eeproms i try. Good tool so far.

Volavka has sorted out my upa usb problem fail i need an adapter omg fail gaveladore

Tight lines and bending rods are what makes my day biggrin Zenter Performance tuning yes bowADBLUE-DTC-FAP-FLAP-EGR-LAMBDA-TQM-TPROT-VMAX-SPECIAL- LAUNCH CONTROL-POPCORN HARDCUT-MANUAL MEDCx17 IMMO OFF 100% - VAG IMMO OFF 2011+ 100% SEAT EDC17C74 2017 IMMO OFF here: bowtime skype:  PM
Reputation: +3 - volavka [+2] , Diagnostix [+1]
Quote this message in a reply
[-] The following 4 users say Thank You to ROD-BENDERS for this post:
  • dara, Diagnostix, Remap Ross, volavka
06-07-2017, 19:24 PM, (This post was last modified: 06-07-2017, 19:29 PM by mikroel.)
Post: #7
RE: Orange 5 clone feedback
(06-07-2017, 19:20 PM)ROD-BENDERS Wrote:  
(06-07-2017, 18:47 PM)mikroel Wrote:  Adapters should be resolder for sure but it isn't so bad ,at all
The main point orange 5 clone isn't so bad as clones can be.
Good investment for sure . smile

So far its reading and writing (with verify) all eeproms i try. Good tool so far.

Volavka has sorted out my upa usb problem fail i need an adapter omg fail gaveladore

I like PIN checking function (test insertions) very much .It saved my job a lot of time.smile
In combination with my UPA -S ,carprog ,and TL866 a lot of job can be done successfully .
Reputation: +3 - ROD-BENDERS [+1] , volavka [+2]
Quote this message in a reply
[-] The following 5 users say Thank You to mikroel for this post:
  • antonypaul, dara, Dinho, JarsaR, volavka
06-07-2017, 19:40 PM, (This post was last modified: 07-07-2017, 17:51 PM by ROD-BENDERS.)
Post: #8
RE: Orange 5 clone feedback
My new xprog 5.70 arrived today with dongle, connect dongle connect usb BOOM yikes usb power surge error fail

I try on another laptop and same thing fxxxx clones devil

Update: Xprog 5.70 working like charm biggrin needed to download fresh software from seller all working without verify errors thumbsup

Tight lines and bending rods are what makes my day biggrin Zenter Performance tuning yes bowADBLUE-DTC-FAP-FLAP-EGR-LAMBDA-TQM-TPROT-VMAX-SPECIAL- LAUNCH CONTROL-POPCORN HARDCUT-MANUAL MEDCx17 IMMO OFF 100% - VAG IMMO OFF 2011+ 100% SEAT EDC17C74 2017 IMMO OFF here: bowtime skype:  PM
Reputation: +1 - dil6222 [+1]
Quote this message in a reply
[-] The following 4 users say Thank You to ROD-BENDERS for this post:
  • antonypaul, dara, dil6222, JarsaR
08-07-2017, 14:07 PM, (This post was last modified: 08-07-2017, 23:55 PM by rs@chip.)
Post: #9
RE: Orange 5 clone feedback
(06-07-2017, 19:40 PM)ROD-BENDERS Wrote:  My new xprog 5.70 arrived today with dongle, connect dongle connect usb BOOM yikes usb power surge error fail

I try on another laptop and same thing fxxxx clones devil

Update: Xprog 5.70 working like charm biggrin needed to download fresh software from seller all working without verify errors thumbsup

yes I have it 5.7 too and work perfect iven on win 10 x64..cas4-cas4+ and many more done no problem.. I also want to buy orange5 did you buy from same site as tm100 mate?
Quote this message in a reply
[-] The following 1 user says Thank You to rs@chip for this post:
  • dara
18-07-2017, 04:53 AM,
Post: #10
RE: Orange 5 clone feedback
Great programmer. All that is stated works. If the speed of exchange is not important, you can do a lot. Many good calculators
Quote this message in a reply
[-] The following 2 users say Thank You to kvihome for this post:
  • dara, Diagnostix


Possibly Related Threads…
Thread Author Replies Views Last Post
0Dash X-tool suppot/Feedback/backup thread volavka 234 79,528 17-03-2020, 18:35 PM
Last Post: tareksadek
0Dash Smok UHDS Support/Feedback/Backup Thread volavka 148 37,709 09-03-2020, 07:44 AM
Last Post: ka_rai
0Dash X-100 PRO Mileage Correction FeedBack ETPerformance 239 94,030 01-03-2020, 19:42 PM
Last Post: Dgordg
0Dash IProg+ & IProgPro suppot/Feedback thread volavka 149 89,562 26-02-2020, 09:54 AM
Last Post: armalek
  2004 JAGUAR XJ6 DASH PINOUT (NEED TO CLONE) Ecutech 2 512 07-01-2020, 13:19 PM
Last Post: Ecutech
0Dash New CLONE Smelecom DSP3 feedback forkade 19 9,505 03-01-2020, 21:50 PM
Last Post: b204e
  VW POLO 2012 POSSIBLE TO CLONE CLUSTER? victorysatgr 2 368 07-12-2019, 01:06 AM
Last Post: Jack Pott
0Dash MTool Mileage Correction suppot/Feedback thread volavka 59 31,207 27-11-2019, 00:47 AM
Last Post: svallecilla
2Autocom Cars Dead Link  ETsmart calculators Softwer doordie40 2 3,132 10-11-2019, 13:24 PM
Last Post: octav_kiss
0Dash MT401 experience feedback zgjana 48 13,532 22-08-2019, 10:06 AM
Last Post: kryspl

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content