Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
READING DME ISN NEED HELP
13-06-2019, 16:07 PM,
Post: #1
|
|||
|
|||
READING DME ISN NEED HELP
Hi, need some more advise , need to do a bmw dme replace , its a 320i facelift, need to know which tools can read isn on bench and write in cas, the dme has water damage, i have read about vvdi and fvdi , can someone please assist on which tools to get to get the job done.
thank you |
|||
14-06-2019, 02:57 AM,
Post: #2
|
|||
|
|||
RE: READING DME ISN NEED HELP
Ktag will be the best for that job.
First try to read full dump from ecu and clone it. If that not help consider reverse order. Try to read ISN from CAS and write it to dme. If I helped, please magic buttons thx+rep
|
|||
14-06-2019, 03:43 AM,
Post: #3
|
|||
|
|||
RE: READING DME ISN NEED HELP
Need more info about the car to give an accurate answer.
|
|||
14-06-2019, 07:53 AM,
Post: #4
|
|||
|
|||
RE: READING DME ISN NEED HELP
(13-06-2019, 16:07 PM)Shinehead Wrote: Hi, need some more advise , need to do a bmw dme replace , its a 320i facelift, need to know which tools can read isn on bench and write in cas, the dme has water damage, i have read about vvdi and fvdi , can someone please assist on which tools to get to get the job done. What engine computer? |
|||
14-06-2019, 11:43 AM,
Post: #5
|
|||
|
|||
RE: READING DME ISN NEED HELP
If it is E90, I usually just swap the flash chip and the new ECU is ready to go (flash has virtual eeprom, so all immo codes copied over)
|
|||
14-06-2019, 17:24 PM,
(This post was last modified: 14-06-2019, 18:07 PM by Shinehead.)
Post: #6
|
|||
|
|||
RE: READING DME ISN NEED HELP
(14-06-2019, 11:43 AM)PhilipM Wrote: If it is E90, I usually just swap the flash chip and the new ECU is ready to go (flash has virtual eeprom, so all immo codes copied over) Thank you,i think i will do tht , can u tell me other compatible dme tht can work there maybe if u have win kfp and check,mine dont work Regards (14-06-2019, 03:43 AM)Enabled Wrote: Need more info about the car to give an accurate answer.Its a e90 2011 model 320i facelift,manual transmission |
|||
15-06-2019, 08:28 AM,
Post: #7
|
|||
|
|||
RE: READING DME ISN NEED HELP
(14-06-2019, 17:24 PM)Shinehead Wrote:(14-06-2019, 11:43 AM)PhilipM Wrote: If it is E90, I usually just swap the flash chip and the new ECU is ready to go (flash has virtual eeprom, so all immo codes copied over) Use CGDI BMW or CG100. |
|||
17-06-2019, 12:41 PM,
Post: #8
|
|||
|
|||
RE: READING DME ISN NEED HELP
(14-06-2019, 02:57 AM)lustek Wrote: Ktag will be the best for that job.hi, can the isn number be written in dme , without expensive tools ?, like auto hex and explorer etc, if possible can u kindly share the procedure.thank you |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content