[muskatas]

Hello mates. What are correct settings for esys to update ZGW(metal case) on F10 (03.10)? MSM and VCM ticks in options off? Connect via gateway?

[lustek]

For esys use enet cable and connect via gateway.
For ISTA+ use icom

[muskatas]

For esys use enet cable and connect via gateway.
For ISTA+ use icom

As I know enet+zgw01 is not the best idea... Icom should be used. If enet is used than u must to "play" whit ip`s that are changing during flashing and losts communication and fails if its not properly configured.

[muskatas]

For esys use enet cable and connect via gateway.
For ISTA+ use icom

As I know enet+zgw01 is not the best idea... Icom should be used. If enet is used than u must to "play" whit ip`s that are changing during flashing and losts communication and fails if its not properly configured.

No one can tell configurations?

[lustek]

For esys use enet cable and connect via gateway.
For ISTA+ use icom

As I know enet+zgw01 is not the best idea... Icom should be used. If enet is used than u must to "play" whit ip`s that are changing during flashing and losts communication and fails if its not properly configured.

No one can tell configurations?

you can use this tutotrial

[Matthew53]

ICOM configuration for dhcp server software (www.dhcpserver.de/cms) or router (May not work with I series Intel processors – require external DHCP server e.g. hardware router)

ICOM Config

ConnectionMode = STATIC_IP
Ip = 192.168.68.85
Netmask = 255.255.255.0
Gateway = 192.168.68.99

DHCPSRV.INI

[SETTINGS]
IPPOOL_1=192.168.68.1-254
IPBIND_1=192.168.68.99
AssociateBindsToPools=1
Trace=1
DeleteOnRelease=0
ExpiredLeaseTimeout=3600

[GENERAL]
LEASETIME=86400
NODETYPE=8
SUBNETMASK=255.255.255.0
NEXTSERVER=192.168.68.99
ROUTER_0=192.168.68.1

[DNS-SETTINGS]
EnableDNS=0

[TFTP-SETTINGS]
EnableTFTP=0
ROOT=C:\Users\Osx\Desktop\DHCP\wwwroot
WritePermission=0

[HTTP-SETTINGS]
EnableHTTP=0
ROOT=C:\Users\Osx\Desktop\DHCP\wwwroot
[00-01-A9-00-EE-E9]
IPADDR=192.168.68.1
AutoConfig=06/26/2016 12:41:32
Hostname=ICOM1120134
LeaseEnd=1467070189


Windows Ethernet config:

"Use the following IP Address"
IP 192.168.68.99
Subnet mask 255.255.255.0

[willisodhiambo]

Funny enough I have updated my F10 with ICOM several times and never had an issue with gateway. I have Icom on DHCP and I have a router configured but never used the router when updating and never had a problem. I simply did not remember ZGW can have issues. Speak of luck?

[dasi]

From what I remember ICOM on DHCP is only required when flashing KOMBI or NBT.
For ZGW, FEM or BDC direct connection is just fine.

[xxiFear]

Well I have the same problem with ENET and ZGW1. It goes into flashing mode then stops Tal processing because of lost connection. From what I know it’s due to the ZGW1 being to slow to get a new IP Adress? But I don’t know how to solve it.

[bmwtechnophobe]

Well I have the same problem with ENET and ZGW1. It goes into flashing mode then stops Tal processing because of lost connection. From what I know it’s due to the ZGW1 being to slow to get a new IP Adress? But I don’t know how to solve it.

When I'm working with a ZGW that is in good shape I have good success in flashing via ENET by following these steps (photos and links attached for clarity):

1. Setup up a DHCP network on your computer device - set your computer's IPv4 address to 169.254.0.4 - Turn OFF all firewalls.
   (instructions attached in file below- restart the computer after the server is installed)
2. Open E-Sys Settings (options -> Settings -> Connections)  add a 0 to the "Additional Transmission Timeout"
   (this gives extra time to the ZGW for a reboot before TAL attempts to write new instructions - restart Esys is mandatory after this step) 
3. Open the connection and connect to your "Gateway" not by VIN - see step 3 photo
   3.b ensure to copy the correct IP address from VIN connection to Gateway With DHCP server RUNNING (note the addresses will always change to 169.254.X.X )
4. Once you connect - execute TAL and Flash ZGW via ENET - will take longer bc of additional Timeout time. You can reset this to default when flashing any other module