Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
ICOMP, ICOM Next Connection problem with ISTA
08-09-2019, 15:00 PM,
Post: #21
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
(08-09-2019, 14:23 PM)Node Wrote: Maybe IToolRadar is not designed for ICOMP? I see port 6801 open so you should be able to connect to a car. All configurations ports seem to be closed which might be expected from the factory tool. I would doubt such as IToolRadar would work because the nvm port 5302 was not on the scanner list. |
|||
08-09-2019, 16:22 PM,
Post: #22
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
Given vnm is not available the only way I see to use this with ISTA+ is through Ediabas in remote mode.
|
|||
08-09-2019, 16:22 PM,
Post: #23
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
any idea how can I connect to car, which settings ISTA VCI Configuration Manager?
thanks |
|||
08-09-2019, 16:37 PM,
Post: #24
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
Choose ediabas there. And configure ediabas in remote mode using IP address of your device.
|
|||
08-09-2019, 16:53 PM,
Post: #25
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
How can I configure ediabas in remote mode using IP address?
it`s ok? Thanks |
|||
08-09-2019, 17:09 PM,
Post: #26
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
INTERFACE = REMOTE
the interface=std:obd line must be starts with ";" Vojnó
Press Thanks and reputation if this post helped you. |
|||
08-09-2019, 17:26 PM,
Post: #27
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
(08-09-2019, 17:09 PM)Vojno Wrote: INTERFACE = REMOTE It doesn't has to start with ";". There is only a # there and it's enough. Only BMW services:
Remote coding/programming - E, F, G serie HDD change, Carplay, Screen mirroring activation FSC pack - CIC, NBT, NBT EVO, ENTRYNAV2, MGU, KAFAS Remote reset 8HP ISN F serie ELV disable for CAS3, 3+ |
|||
08-09-2019, 17:31 PM,
Post: #28
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
(08-09-2019, 17:26 PM)Matthew53 Wrote:(08-09-2019, 17:09 PM)Vojno Wrote: INTERFACE = REMOTE Yes! I mean this is the good: ; INTERFACE =STD:OBD INTERFACE =REMOTE Vojnó
Press Thanks and reputation if this post helped you. |
|||
08-09-2019, 17:34 PM,
Post: #29
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
(08-09-2019, 17:31 PM)Vojno Wrote:(08-09-2019, 17:26 PM)Matthew53 Wrote:(08-09-2019, 17:09 PM)Vojno Wrote: INTERFACE = REMOTE Maybe it's correct too, but it's always set as default like this: Interface = REMOTE #Interface = STD:OBD Only BMW services:
Remote coding/programming - E, F, G serie HDD change, Carplay, Screen mirroring activation FSC pack - CIC, NBT, NBT EVO, ENTRYNAV2, MGU, KAFAS Remote reset 8HP ISN F serie ELV disable for CAS3, 3+ |
|||
08-09-2019, 17:54 PM,
Post: #30
|
|||
|
|||
RE: ICOMP, ICOM Next Connection problem with ISTA
with Ediabas (VCI ISTA) and
Ediabas Ini INTERFACE =STD:OBD #INTERFACE =REMOTE the vehicle could not be identified |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content