[m1ke]

Genuine pcm flash and Scanmatik and Module 71 EDC17CP49 on bench R/W work perfect with checks etc.

[lsalt100]

Genuine pcm flash and Scanmatik SM2- Module 84
delphi DCM6.2 skoda 1.6l TDI CXXB 04L906056CL
VR + obd flash, all OK

[PsiDOC]

Genuine Scanmatik Pro 2.
Genuine PCM flash with module 71.
Only had 1 brick after erase and this was due to a faulty USB cable, so please, use a high quality USB cable.
100% confidence in this setup.

[youberser]

For now, is working perfectly, I have clone 67 in 1

The only thing that dont works is if I remove tprot, Im not able to read the ecu from OBD cable. Only chance to read and write is on the bench.

Also, when I try to flash, there is a option in pcm to remove tampering protect, If I check that, the programs outputs an error

[ROD-BENDERS]

For now, is working perfectly, I have clone 67 in 1

The only thing that dont works is if I remove tprot, Im not able to read the ecu from OBD cable. Only chance to read and write is on the bench.

Also, when I try to flash, there is a option in pcm to remove tampering protect, If I check that, the programs outputs an error

Post up your solution to that ecu and tell us which one please

[youberser]

For now, is working perfectly, I have clone 67 in 1

The only thing that dont works is if I remove tprot, Im not able to read the ecu from OBD cable. Only chance to read and write is on the bench.

Also, when I try to flash, there is a option in pcm to remove tampering protect, If I check that, the programs outputs an error

Post up your solution to that ecu and tell us which one please

I've attached the file with the files I'm working, After flashing the tprot off file on bench, the car runs fine, but I can't read/write from OBD port (Tried with PCM flash and MPPS)

I will attach a photo of the error that PCM Flash outputs (when I tick the option to remove tampering protection before writing any file on the ecu) ASAP

[batja]

For now, is working perfectly, I have clone 67 in 1

The only thing that dont works is if I remove tprot, Im not able to read the ecu from OBD cable. Only chance to read and write is on the bench.

Also, when I try to flash, there is a option in pcm to remove tampering protect, If I check that, the programs outputs an error

Post up your solution to that ecu and tell us which one please

I've attached the file with the files I'm working, After flashing the tprot off file on bench, the car runs fine, but I can't read/write from OBD port (Tried with PCM flash and MPPS)

I will attach a photo of the error that PCM Flash outputs (when I tick the option to remove tampering protection before writing any file on the ecu) ASAP

BMW with pcmflash via OBD? I believe that you are dreaming

[al70]

My opinion, obd reading/writing with clones on cars after 08/09 especially vag cars is like throwing a round dice, if an ECU is opened properly, reading directly from the board will always be my choice, I get panic attacks when I plug my kess clone in for a virtual write , goodluck

[fifii69]

I got ori pcmflash, I have done many bmw edc17cp45 ,c41, c50 edc17 vag ,renault, opel edc17,bench mode protocol 71 , many mazda SH ecu obd r/w crypto and no crypto and many more ecu it's good tool but not cover all ecu so I got AT too

[JorBo]

PcmFlash Ori.

Scanmatik2 Pro and Openport 2.0.

Modules: 48, 50, 57, 58, 62, 71, 77

Tested all with many Ecu´s OBD and Bench Mode, pcr2.1 unlock R/W , clone edc16 and edc17. Works perfect.

Very good support from the owner also.