[eltoke]

Hello everyone.

I have a speed limit problem with a 2012 W906 sprinter. Although this is a topic widely discussed in the forum, it is not very clear. Generally the topic is closed without a solution or the possible answers are not clear.

I have struggled quite a bit with this car and cannot clear the 65 Mile speed limit.
I have a flash and eeprom reading from the ECU, but as I have been able to see the VMax in the ECU is Off (some expert check the dump and correct me if that is not the case). I tried to eliminate it with Autel IM608, although it allows me to modify the coding, the car is still limited to 65 miles. Attached image of autel.
I tried to do the process with xentry offline but when I modify the speed limit within the SCN encoding it gives me a communication error 8.561.6067. According to what I have asked to read, this error is because the function of allowing modification of the ECU must be activated within the developer options (I cannot find this option).

I have Xentry Offline installed with Autel VCI passthru, I have DTS Monaco 8.14 on my laptop, but I have never worked with it, I must also configure it in passthru mode to work with the Autel IM608 VCI.

Some of the Mercedes experts on the forum can help me solve this problem.

Thank you so much

[DSESET86]

Hello everyone.

I have a speed limit problem with a 2012 W906 sprinter. Although this is a topic widely discussed in the forum, it is not very clear. Generally the topic is closed without a solution or the possible answers are not clear.

I have struggled quite a bit with this car and cannot clear the 65 Mile speed limit.
I have a flash and eeprom reading from the ECU, but as I have been able to see the VMax in the ECU is Off (some expert check the dump and correct me if that is not the case). I tried to eliminate it with Autel IM608, although it allows me to modify the coding, the car is still limited to 65 miles. Attached image of autel.
I tried to do the process with xentry offline but when I modify the speed limit within the SCN encoding it gives me a communication error 8.561.6067. According to what I have asked to read, this error is because the function of allowing modification of the ECU must be activated within the developer options (I cannot find this option).

I have Xentry Offline installed with Autel VCI passthru, I have DTS Monaco 8.14 on my laptop, but I have never worked with it, I must also configure it in passthru mode to work with the Autel IM608 VCI.

Some of the Mercedes experts on the forum can help me solve this problem.

Thank you so much

Speed limit adjustment is done by dts monaco or vediamo. The ecu must be unlocked with a seed key generator. Only then, you can adjust the scn coding and change the speed limit. I've also successfully adjusted the speed limit with DAS developer mode + c4 clone interface. I have no experience using autel j2534 with DAS or monaco.

[eltoke]

Hello everyone.

I have a speed limit problem with a 2012 W906 sprinter. Although this is a topic widely discussed in the forum, it is not very clear. Generally the topic is closed without a solution or the possible answers are not clear.

I have struggled quite a bit with this car and cannot clear the 65 Mile speed limit.
I have a flash and eeprom reading from the ECU, but as I have been able to see the VMax in the ECU is Off (some expert check the dump and correct me if that is not the case). I tried to eliminate it with Autel IM608, although it allows me to modify the coding, the car is still limited to 65 miles. Attached image of autel.
I tried to do the process with xentry offline but when I modify the speed limit within the SCN encoding it gives me a communication error 8.561.6067. According to what I have asked to read, this error is because the function of allowing modification of the ECU must be activated within the developer options (I cannot find this option).

I have Xentry Offline installed with Autel VCI passthru, I have DTS Monaco 8.14 on my laptop, but I have never worked with it, I must also configure it in passthru mode to work with the Autel IM608 VCI.

Some of the Mercedes experts on the forum can help me solve this problem.

Thank you so much

Speed limit adjustment is done by dts monaco or vediamo. The ecu must be unlocked with a seed key generator. Only then, you can adjust the scn coding and change the speed limit. I've also successfully adjusted the speed limit with DAS developer mode + c4 clone interface. I have no experience using autel j2534 with DAS or monaco.

Hello and DSESET86
I managed to enter Xentry developer mode, but I can't find among all the options that appear which one allows you to unlock the ecu.
It's a huge list of settings.

[DSESET86]

Hello everyone.

I have a speed limit problem with a 2012 W906 sprinter. Although this is a topic widely discussed in the forum, it is not very clear. Generally the topic is closed without a solution or the possible answers are not clear.

I have struggled quite a bit with this car and cannot clear the 65 Mile speed limit.
I have a flash and eeprom reading from the ECU, but as I have been able to see the VMax in the ECU is Off (some expert check the dump and correct me if that is not the case). I tried to eliminate it with Autel IM608, although it allows me to modify the coding, the car is still limited to 65 miles. Attached image of autel.
I tried to do the process with xentry offline but when I modify the speed limit within the SCN encoding it gives me a communication error 8.561.6067. According to what I have asked to read, this error is because the function of allowing modification of the ECU must be activated within the developer options (I cannot find this option).

I have Xentry Offline installed with Autel VCI passthru, I have DTS Monaco 8.14 on my laptop, but I have never worked with it, I must also configure it in passthru mode to work with the Autel IM608 VCI.

Some of the Mercedes experts on the forum can help me solve this problem.

Thank you so much

Speed limit adjustment is done by dts monaco or vediamo. The ecu must be unlocked with a seed key generator. Only then, you can adjust the scn coding and change the speed limit. I've also successfully adjusted the speed limit with DAS developer mode + c4 clone interface. I have no experience using autel j2534 with DAS or monaco.

Hello and DSESET86
I managed to enter Xentry developer mode, but I can't find among all the options that appear which one allows you to unlock the ecu.
It's a huge list of settings.

I can take a look through teamviewer.

[eltoke]

Hello everyone.

I have a speed limit problem with a 2012 W906 sprinter. Although this is a topic widely discussed in the forum, it is not very clear. Generally the topic is closed without a solution or the possible answers are not clear.

I have struggled quite a bit with this car and cannot clear the 65 Mile speed limit.
I have a flash and eeprom reading from the ECU, but as I have been able to see the VMax in the ECU is Off (some expert check the dump and correct me if that is not the case). I tried to eliminate it with Autel IM608, although it allows me to modify the coding, the car is still limited to 65 miles. Attached image of autel.
I tried to do the process with xentry offline but when I modify the speed limit within the SCN encoding it gives me a communication error 8.561.6067. According to what I have asked to read, this error is because the function of allowing modification of the ECU must be activated within the developer options (I cannot find this option).

I have Xentry Offline installed with Autel VCI passthru, I have DTS Monaco 8.14 on my laptop, but I have never worked with it, I must also configure it in passthru mode to work with the Autel IM608 VCI.

Some of the Mercedes experts on the forum can help me solve this problem.

Thank you so much

Speed limit adjustment is done by dts monaco or vediamo. The ecu must be unlocked with a seed key generator. Only then, you can adjust the scn coding and change the speed limit. I've also successfully adjusted the speed limit with DAS developer mode + c4 clone interface. I have no experience using autel j2534 with DAS or monaco.

Hello and DSESET86
I managed to enter Xentry developer mode, but I can't find among all the options that appear which one allows you to unlock the ecu.
It's a huge list of settings.

I can take a look through teamviewer.

I will arrive home in 1 hour, I don't know if you will be available?